On 7/13/06, Stephen Hemminger <shemminger at osdl.org> wrote: > On Thu, 13 Jul 2006 14:10:57 -0500 > "Ezsra McDonald" <ezsra.mcdonald at gmail.com> wrote: > > > I have read several articles for setting up a network bridge. > > > > My configuration is: > > > > WorkStation --> Switch0:VLAN1 --> Switch1:VLAN1 --> bridge --> > > Switch1:VLAN45 --> Laptop > > > > I am running CentOS 4.3 on the bridge > > > > > > #> brctl show > > bridge name bridge id STP enabled interfaces > > br0 8000.0030843e5aa2 no eth1 > > eth2 > > > > I followed the instructions at : > > > > http://www.linuxjournal.com/article/8172 > > > > Read the wiki > http://linux-net.osdl.org/index.php/Bridge Yep, read that one too. > > > I can't ping the laptop nor can the laptop ping my workstation. I put > > an IP on br0 and tried to ping out and got nothing. tcpdump shows no > > traffic except for an arp request from the laptop. > > > > Was I supposed to recompile my kernel? I saw at least one article that > > recommended recompilig the kernel with a couple of config changes. I > > have the latest stock 2.6 kernel RPM installed. Do we need to do any kernel compilations? Are the stock kernels ok? I do see the "bridge" module loaded with an lsmod. > > > > Do I need to do any special configuration on the switches like setting > > the port to do port monitoring or anything like that? Its a Cisco 2900 > > switch. Any suggestions here? Enable port monitoring or no? > > > > Any help would be appreciated. > > Look at the status of the interfaces. > # brctl showstp br0 > [root at staff-bridge ~]# brctl showstp br0 br0 bridge id 8000.001346998d68 designated root 8000.001346998d68 root port 0 path cost 0 max age 19.99 bridge max age 19.99 hello time 1.99 bridge hello time 1.99 forward delay 14.99 bridge forward delay 14.99 ageing time 299.95 hello timer 1.14 tcn timer 0.00 topology change timer 0.00 gc timer 0.00 flags eth1 (1) port id 8001 state disabled designated root 8000.001346998d68 path cost 19 designated bridge 8000.001346998d68 message age timer 0.00 designated port 8001 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags eth2 (2) port id 8002 state disabled designated root 8000.001346998d68 path cost 19 designated bridge 8000.001346998d68 message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags > Perhaps one or more interfaces are not reporting carrier. > Also, because the implementation of STP inside doesn't know about VLAN's > other switches may turn off the port because of seeing STP packets. > eth1 Link encap:Ethernet HWaddr 00:13:46:99:8D:6A inet6 addr: fe80::213:46ff:fe99:8d6a/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:537728 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:108031928 (103.0 MiB) TX bytes:0 (0.0 b) Interrupt:3 Base address:0xe400 eth2 Link encap:Ethernet HWaddr 00:13:46:99:8D:68 inet6 addr: fe80::213:46ff:fe99:8d68/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:115688 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8363266 (7.9 MiB) TX bytes:0 (0.0 b) Interrupt:9 Base address:0x800
