On Sun, Jan 30, 2022 at 09:45:49PM +0100, Hans de Goede wrote:
> From: Yauhen Kharuzhy <jekhor@xxxxxxxxx>
>
> Add a "linux,pump-express-vbus-max" property which indicates if the Pump
> Express+ protocol should be used to increase the charging protocol.
>
> If this new property is set and a DCP charger is detected then request
> a higher charging voltage through the Pump Express+ protocol.
>
> So far this new property is only used on x86/ACPI (non devicetree) devs,
> IOW it is not used in actual devicetree files. The devicetree-bindings
> maintainers have requested properties like these to not be added to the
> devicetree-bindings, so the new property is deliberately not added
> to the existing devicetree-bindings.
>
> Changes by Hans de Goede:
> - Port to my bq25890 patch-series + various cleanups
> - Make behavior configurable through a new "linux,pump-express-vbus-max"
> device-property
> - Sleep 1 second before re-checking the Vbus voltage after requesting
> it to be raised, to ensure that the ADC has time to sampled the new Vbus
> - Add VBUSV bq25890_tables[] entry and use it in bq25890_get_vbus_voltage()
> - Tweak commit message
...
> +static void bq25890_pump_express_work(struct work_struct *data)
> +{
> + struct bq25890_device *bq =
> + container_of(data, struct bq25890_device, pump_express_work.work);
> + int voltage, i, ret;
> +
> + dev_dbg(bq->dev, "Start to request input voltage increasing\n");
> +
> + /* Enable current pulse voltage control protocol */
> + ret = bq25890_field_write(bq, F_PUMPX_EN, 1);
> + if (ret < 0)
> + goto error_print;
> +
> + for (i = 0; i < PUMP_EXPRESS_MAX_TRIES; i++) {
> + voltage = bq25890_get_vbus_voltage(bq);
> + if (voltage < 0)
> + goto error_print;
It also can be (at least in align with the rest error paths)
ret = bq25890_get_vbus_voltage(bq);
if (ret < 0)
goto error_print;
voltage = ret;
followed up (but not necessarily)...
> + dev_dbg(bq->dev, "input voltage = %d uV\n", voltage);
> +
> + if ((voltage + PUMP_EXPRESS_VBUS_MARGIN_uV) >
> + bq->pump_express_vbus_max)
> + break;
> +
> + ret = bq25890_field_write(bq, F_PUMPX_UP, 1);
> + if (ret < 0)
> + goto error_print;
> +
> + /* Note a single PUMPX up pulse-sequence takes 2.1s */
> + ret = regmap_field_read_poll_timeout(bq->rmap_fields[F_PUMPX_UP],
> + ret, !ret, 100000, 3000000);
> + if (ret < 0)
> + goto error_print;
> +
> + /* Make sure ADC has sampled Vbus before checking again */
> + msleep(1000);
> + }
> +
> + bq25890_field_write(bq, F_PUMPX_EN, 0);
> +
> + dev_info(bq->dev, "Hi-voltage charging requested, input voltage is %d mV\n",
> + voltage);
> + return;
> +error_print:
if (ret < 0)
But it's up to you.
> + dev_err(bq->dev, "Failed to request hi-voltage charging\n");
> +}
--
With Best Regards,
Andy Shevchenko
