On Thu, Dec 18, 2008 at 12:26 AM, David Shay <davideshay@xxxxxxxxx> wrote:
I'm having a problem with the device listed above.Relevant facts:DVICO FusionHDTV5 USB device (USB device ID 0fe9:d501)Gentoo 2.6.26, running kernel gentoo-sources 2.6.26-r4 (dvb drivers initially from kernel only)The following is the dmesg log at bootup:dvb-usb: found a 'DViCO FusionHDTV5 USB Gold' in warm state.i2c-adapter i2c-1: adapter [DViCO FusionHDTV5 USB Gold] registereddvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.DVB: registering new adapter (DViCO FusionHDTV5 USB Gold)DVB: Unable to find symbol lgdt330x_attach()dvb-usb: no frontend was attached by 'DViCO FusionHDTV5 USB Gold'input: IR-receiver inside an USB DVB receiver as /class/input/input5dvb-usb: schedule remote query interval to 100 msecs.dvb-usb: DViCO FusionHDTV5 USB Gold successfully initialized and connected.usbcore: registered new interface driver dvb_usb_cxusbMain error here is the unable to find symbol lgdt330x_attach() line. Not sure what is happening here. Was on #linuxtv last night and on a hunch, we disconnected the device, manually modprobe'd lgdt330x and reconnected, and all was fine. Recommendation was to install from the latest drivers from mercurial, which I have done. I still get the same symptoms as indicated above. If I then disconnect and reconnect (even without the modprobe), I get the rest of the log, as indicated below, which makes everything successful:
I was wrong about this and obviously didn't read very well after midnight. I *DID INDEED* have to manually modprobe to get further. However, now I get a new error:
i2c-adapter i2c-1: adapter [DViCO FusionHDTV5 USB Gold] unregistered
dvb-usb: DViCO FusionHDTV5 USB Gold successfully deinitialized and disconnected.
usb 1-4: new high speed USB device using ehci_hcd and address 6
usb 1-4: configuration #1 chosen from 1 choice
dvb-usb: found a 'DViCO FusionHDTV5 USB Gold' in cold state, will try to load a
firmware
firmware: requesting dvb-usb-bluebird-01.fw
dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw'
usb 1-4: USB disconnect, address 6
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
usb 1-4: new high speed USB device using ehci_hcd and address 7
usb 1-4: configuration #1 chosen from 1 choice
dvb-usb: found a 'DViCO FusionHDTV5 USB Gold' in warm state.
i2c-adapter i2c-1: adapter [DViCO FusionHDTV5 USB Gold] registered
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (DViCO FusionHDTV5 USB Gold)
i2c-adapter i2c-1: master_xfer[0] W, addr=0x0e, len=1
i2c-adapter i2c-1: master_xfer[1] R, addr=0x0e, len=1
DVB: registering adapter 0 frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)
...
DVB: Unable to find symbol simple_tuner_attach()
input: IR-receiver inside an USB DVB receiver as /class/input/input7
dvb-usb: schedule remote query interval to 100 msecs.
dvb-usb: DViCO FusionHDTV5 USB Gold successfully initialized and connected.
Note that now I get the error about "simple_tuner_attach". Argh.
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
