|
Hello everyone ! I have a problem with a WinTV HVR 1700 I installed the latest available driver via mercurial and the firmware (dvb-fe-tda10048-1.0.fw). The card seems to be well detected by its module (cx23885) as you can see in the dmesg output. I saw there [1] that some others firmware were used (v4l-cx23885-avcore-01.fw and v4l-cx23885-enc.fw). I installed them, but I don't see when they are loaded. I am sure of the frequencies I used because I have successfully tested on the same antenna, with the same frequencies with a WinTV Nova-T. I do not see where the problem can come from. [1] http://marc.info/?l=linux-dvb&m=120951119026705&w=2 Thank you very much for any help. Simon MORIN ------ dmesg output : Linux video capture interface: v2.00 cx23885 driver version 0.0.1 loaded ACPI: PCI Interrupt 0000:0e:00.0[A] -> GSI 17 (level, low) -> IRQ 17 cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge type 885 cx23885[0]/0: cx23885_init_tsport(portno=2) CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700 [card=8,autodetected] cx23885[0]/0: cx23885_pci_quirks() cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0 cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0 cx23885[0]/0: cx23885_reset() cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A] cx23885[0]/0: cx23885_sram_channel_setup() 0x000104c0 <- 0x00000040 cx23885[0]/0: cx23885_sram_channel_setup() 0x000104d0 <- 0x00000b80 cx23885[0]/0: cx23885_sram_channel_setup() 0x000104e0 <- 0x000016c0 cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B] cx23885[0]/0: cx23885_sram_channel_setup() 0x00010580 <- 0x00005000 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010590 <- 0x000052f0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105a0 <- 0x000055e0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105b0 <- 0x000058d0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105c0 <- 0x00005bc0 cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C] cx23885[0]/0: cx23885_sram_channel_setup() 0x000105e0 <- 0x00006000 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105f0 <- 0x000062f0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010600 <- 0x000065e0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010610 <- 0x000068d0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010620 <- 0x00006bc0 cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9] cx23885[0]: i2c scan: found device @ 0x10 [tda10048] cx23885[0]: i2c scan: found device @ 0xa0 [eeprom] cx23885[0]: i2c scan: found device @ 0x84 [tda8295] cx25840' 2-0044: cx25 0-21 found @ 0x88 (cx23885[0]) cx23885[0]: i2c scan: found device @ 0x66 [???] cx23885[0]: i2c scan: found device @ 0x88 [cx25837] cx23885[0]: i2c scan: found device @ 0x98 [???] tveeprom 0-0050: Hauppauge model 81519, rev B2E9, serial# 3473167 tveeprom 0-0050: MAC address is 00-0D-FE-34-FF-0F tveeprom 0-0050: tuner model is Philips 18271_8295 (idx 149, type 54) tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 0-0050: audio processor is CX23885 (idx 39) tveeprom 0-0050: decoder processor is CX23885 (idx 33) tveeprom 0-0050: has no radio cx23885[0]: hauppauge eeprom: model=81519 cx23885_dvb_register() allocating 1 frontend(s) cx23885[0]: cx23885 based dvb card tda829x 1-0042: type set to tda8295 tda18271 1-0060: creating new instance TDA18271HD/C1 detected @ 1-0060 DVB: registering new adapter (cx23885[0]) DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:0e:00.0, rev: 2, irq: 17, latency: 0, mmio: 0xfde00000 PCI: Setting latency timer of device 0000:0e:00.0 to 64 tda10048_firmware_upload: waiting for firmware upload (dvb-fe-tda10048-1.0.fw)... firmware: requesting dvb-fe-tda10048-1.0.fw tda10048_firmware_upload: firmware read 24878 bytes. tda10048_firmware_upload: firmware uploading tda10048_firmware_upload: firmware uploaded ----- Modules loaded : #$ modprobe -v cx23885 insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/tveeprom.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/btcx-risc.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/videobuf-core.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/dvb/dvb-core/dvb-core.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/videobuf-dvb.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/videobuf-dma-sg.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/cx2341x.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/v4l2-compat-ioctl32.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/v4l1-compat.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/videodev.ko insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/cx23885/cx23885.ko debug=5 i2c_scan=1 |
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
