Hello, I am trying to get my WinTV-HVR-1500 working. I am using the ~stoth/cx23885-audio repository, which seems to be the only one with HVR-1500 analog support, but I am getting an error in the firmware step for the tuner chip. dmesg looks like this: [ 1099.493745] Linux video capture interface: v2.00 [ 1099.503677] cx23885 driver version 0.0.1 loaded [ 1099.503732] cx23885 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1099.503810] CORE cx23885[0]: subsystem: 0070:7790, board: Hauppauge WinTV-HVR1500 [card=6,insmod option] [ 1099.612900] cx23885[0]: i2c bus 0 registered [ 1099.613604] cx23885[0]: i2c bus 1 registered [ 1099.614250] cx23885[0]: i2c bus 2 registered [ 1099.642338] tveeprom 0-0050: Encountered bad packet header [ff]. Corrupt or not a Hauppauge eeprom. [ 1099.642344] cx23885[0]: warning: unknown hauppauge model #0 [ 1099.642346] cx23885[0]: hauppauge eeprom: model=0 [ 1099.651724] cx25840' 2-0044: cx25 0-21 found @ 0x88 (cx23885[0]) [ 1099.666656] tuner' 1-0061: chip found @ 0xc2 (cx23885[0]) [ 1099.687281] xc2028 1-0061: creating new instance [ 1099.687288] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner [ 1099.692057] xc2028 1-0061: destroying instance [ 1099.692142] xc2028 1-0061: creating new instance [ 1099.692144] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner [ 1099.692280] cx23885[0]/0: registered device video0 [v4l2] [ 1099.692610] cx23885[0]/1: registered ALSA audio device [ 1099.692616] firmware: requesting xc3028-v27.fw [ 1099.848072] xc2028 1-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7 [ 1100.046592] xc2028 1-0061: Loading firmware for type=BASE (1), id 0000000000000000. [ 1100.667376] xc2028 1-0061: i2c output error: rc = -5 (should be 64) [ 1100.667384] xc2028 1-0061: -5 returned from send [ 1100.667388] xc2028 1-0061: Error -22 while loading base firmware [ 1100.918459] xc2028 1-0061: Loading firmware for type=BASE (1), id 0000000000000000. [ 1101.487794] xc2028 1-0061: i2c output error: rc = -5 (should be 64) [ 1101.487803] xc2028 1-0061: -5 returned from send [ 1101.487807] xc2028 1-0061: Error -22 while loading base firmware [ 1101.491986] firmware: requesting v4l-cx23885-avcore-01.fw [ 1102.220875] cx25840' 2-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes) [ 1102.235880] cx23885[0]: cx23885 based dvb card [ 1102.287830] xc2028 1-0061: attaching existing instance [ 1102.287839] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner [ 1102.289726] DVB: registering new adapter (cx23885[0]) [ 1102.290448] DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... [ 1102.319882] cx23885_dev_checkrevision() Hardware revision = 0xb0 [ 1102.319899] cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 18, latency: 0, mmio: 0xa8400000 [ 1102.319911] cx23885 0000:03:00.0: setting latency timer to 64 Thanks for any help! - Dan _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
