Hello,
I have quite an interesting problem on a system with 6 tuners, basically the system 'locks up' completely after a short period of fairly intensive use, only a power-cycle can bring the system back to life. I first experienced this since building the system with Fedora Core 9 fully updated (2.6.26.5-45.fc9.i686). I spotted some cx88 changes in the 2.6.27 release notes and so upgraded to Fedora Core 10 / Rawhide and I am still experiencing the same problem on 2.6.27.4-58.fc10.i686.
The problem appears when I run a simple script which controls all available tuners simultaneously and tunes (szap) to a range of transponders before running tests (dvbsnoop -s pidscan) on the content of each. This morning I grabbed the latest v4l-dvb source tree (http://linuxtv.org/hg/v4l-dvb) and built it for my 2.6.27.4-58.fc10.i686 kernel and I am still experiencing the same problem.
Up until this morning I have been limited to the 5 x KWorld DVB-S 100 tuners as the stock Fedora kernel didn't support the Hauppauge WinTV-HVR4000(Lite) board. So the problem existed before the HVR4000 was included in the loop.
I have attached various bits of debug, its tricky to try and diagnose the real cause as the machine completely freezes and doesn't respond to anything. I have tested the rest of the hardware (memtest, cpu burn-in-tests etc.) and the system is otherwise perfectly stable. But if I run the script to utilise all the tuners for a few minutes to an hour and the machine locks up.
Any ideas? suggestions?
Regards,
MC
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.27.4-58.fc10.i686 (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxx)
(gcc version 4.3.2 20081007 (Red Hat 4.3.2-6) (GCC) ) #1 SMP Mon Oct 27
18:21:44 EDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000c7fa0000 (usable)
BIOS-e820: 00000000c7fa0000 - 00000000c7fae000 (ACPI data)
BIOS-e820: 00000000c7fae000 - 00000000c7fe0000 (ACPI NVS)
BIOS-e820: 00000000c7fe0000 - 00000000c8000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
last_pfn = 0xc7fa0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 30000000 @ 7000-c000
Using x86 segment limits to approximate NX protection
RAMDISK: 37c89000 - 37fefd72
Allocated new RAMDISK: 0098e000 - 00cf4d72
Move RAMDISK from 0000000037c89000 - 0000000037fefd71 to 0098e000 - 00cf4d71
DMI 2.4 present.
ACPI: RSDP 000FAF00, 0014 (r0 ACPIAM)
ACPI: RSDT C7FA0000, 0038 (r1 A_M_I_ OEMRSDT 9000704 MSFT 97)
ACPI: FACP C7FA0200, 0084 (r2 A_M_I_ OEMFACP 9000704 MSFT 97)
ACPI: DSDT C7FA0440, 6A9A (r1 A0888 A0888000 0 INTL 20051117)
ACPI: FACS C7FAE000, 0040
ACPI: APIC C7FA0390, 006C (r1 A_M_I_ OEMAPIC 9000704 MSFT 97)
ACPI: MCFG C7FA0400, 003C (r1 A_M_I_ OEMMCFG 9000704 MSFT 97)
ACPI: OEMB C7FAE040, 0080 (r1 A_M_I_ AMI_OEM 9000704 MSFT 97)
ACPI: HPET C7FA6EE0, 0038 (r1 A_M_I_ OEMHPET 9000704 MSFT 97)
2431MB HIGHMEM available.
768MB LOWMEM available.
mapped low ram: 0 - 30000000
low ram: 00000000 - 30000000
bootmap 00008000 - 0000e000
(9 early reservations) ==> bootmem [0000000000 - 0030000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000400000 - 00009891d8] TEXT DATA BSS ==> [0000400000 - 00009891d8]
#4 [000098a000 - 000098e000] INIT_PG_TABLE ==> [000098a000 - 000098e000]
#5 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
#7 [000098e000 - 0000cf4d72] NEW RAMDISK ==> [000098e000 - 0000cf4d72]
#8 [0000008000 - 000000e000] BOOTMAP ==> [0000008000 - 000000e000]
found SMP MP-table at [c00ff780] 000ff780
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00030000
HighMem 0x00030000 -> 0x000c7fa0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x000c7fa0
On node 0 totalpages: 819007
free_area_init_node: node 0, pgdat c0818700, node_mem_map c1000000
DMA zone: 3967 pages, LIFO batch:0
Normal zone: 191008 pages, LIFO batch:31
HighMem zone: 617632 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 4 CPUs, 2 hotplug CPUs
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
Allocating PCI resources starting at cc000000 (gap: c8000000:36e00000)
PERCPU: Allocating 41372 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 4, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 812607
Kernel command line: ro root=UUID=3339a987-9d26-43ba-b9bb-7fb98d046595 rhgb
quiet vmalloc=256M
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c08b2000 soft=c0892000
PID hash table entries: 4096 (order: 12, 16384 bytes)
TSC: Unable to calibrate against PIT
TSC: using PMTIMER reference calibration
Detected 2660.972 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3239252k/3276416k available (2854k kernel code, 35900k reserved, 1430k
data, 360k init, 2489984k highmem)
virtual kernel memory layout:
fixmap : 0xffc57000 - 0xfffff000 (3744 kB)
pkmap : 0xff400000 - 0xff800000 (4096 kB)
vmalloc : 0xf0800000 - 0xff3fe000 ( 235 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
.init : 0xc0835000 - 0xc088f000 ( 360 kB)
.data : 0xc06c9b76 - 0xc082f680 (1430 kB)
.text : 0xc0400000 - 0xc06c9b76 (2854 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency..
5321.94 BogoMIPS (lpj=2660972)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys devices
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 3072K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU E7300 @ 2.66GHz stepping 06
CPU 1 irqstacks, hard=c08b3000 soft=c0893000
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5321.95 BogoMIPS
(lpj=2660979)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 3072K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU E7300 @ 2.66GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (10643.90 BogoMIPS).
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=184 bytes
sizeof(task_struct)=3264 bytes
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
net_namespace: 840 bytes
Booting paravirtualized kernel on bare hardware
Time: 11:39:12 Date: 10/30/08
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub
without MMCONFIG support.
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
PCI: 0000:00:1b.0 reg 10 64bit mmio: [cdff8000, cdffbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
PCI: 0000:00:1d.0 reg 20 io port: [9000, 901f]
PCI: 0000:00:1d.1 reg 20 io port: [9400, 941f]
PCI: 0000:00:1d.2 reg 20 io port: [9800, 981f]
PCI: 0000:00:1d.3 reg 20 io port: [a000, a01f]
PCI: 0000:00:1d.7 reg 10 32bit mmio: [cdfff800, cdfffbff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
PCI: 0000:00:1f.1 reg 18 io port: [0, 7]
PCI: 0000:00:1f.1 reg 1c io port: [0, 3]
PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf]
PCI: 0000:00:1f.2 reg 10 io port: [b800, b807]
PCI: 0000:00:1f.2 reg 14 io port: [b400, b403]
PCI: 0000:00:1f.2 reg 18 io port: [b000, b007]
PCI: 0000:00:1f.2 reg 1c io port: [a800, a803]
PCI: 0000:00:1f.2 reg 20 io port: [a400, a40f]
PCI: 0000:00:1f.2 reg 24 32bit mmio: [cdfffc00, cdffffff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
PCI: 0000:00:1f.3 reg 20 io port: [400, 41f]
PCI: 0000:03:00.0 reg 10 32bit mmio: [de000000, deffffff]
PCI: 0000:03:00.0 reg 14 32bit mmio: [e0000000, efffffff]
PCI: 0000:03:00.0 reg 1c 64bit mmio: [dd000000, ddffffff]
PCI: 0000:03:00.0 reg 30 32bit mmio: [dcfe0000, dcffffff]
Pre-1.1 PCIe device detected, disable ASPM for 0000:00:01.0. It can be enabled
forcedly with 'pcie_aspm=force'
PCI: bridge 0000:00:01.0 io port: [e000, efff]
PCI: bridge 0000:00:01.0 32bit mmio: [dcf00000, deffffff]
PCI: bridge 0000:00:01.0 64bit mmio pref: [e0000000, efffffff]
PCI: 0000:02:00.0 reg 10 io port: [d800, d8ff]
PCI: 0000:02:00.0 reg 18 64bit mmio: [dceff000, dcefffff]
PCI: 0000:02:00.0 reg 20 32bit mmio: [dfff0000, dfffffff]
PCI: 0000:02:00.0 reg 30 32bit mmio: [dcec0000, dcedffff]
pci 0000:02:00.0: supports D1
pci 0000:02:00.0: supports D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
PCI: bridge 0000:00:1c.0 io port: [d000, dfff]
PCI: bridge 0000:00:1c.0 32bit mmio: [dce00000, dcefffff]
PCI: bridge 0000:00:1c.0 64bit mmio pref: [dff00000, dfffffff]
PCI: 0000:01:00.0 reg 10 32bit mmio: [ce000000, ceffffff]
PCI: 0000:01:00.2 reg 10 32bit mmio: [cf000000, cfffffff]
PCI: 0000:01:01.0 reg 10 32bit mmio: [d0000000, d0ffffff]
PCI: 0000:01:01.2 reg 10 32bit mmio: [d1000000, d1ffffff]
PCI: 0000:01:02.0 reg 10 32bit mmio: [d2000000, d2ffffff]
PCI: 0000:01:02.2 reg 10 32bit mmio: [d3000000, d3ffffff]
PCI: 0000:01:03.0 reg 10 32bit mmio: [d4000000, d4ffffff]
PCI: 0000:01:03.2 reg 10 32bit mmio: [d5000000, d5ffffff]
PCI: 0000:01:04.0 reg 10 32bit mmio: [d6000000, d6ffffff]
PCI: 0000:01:04.2 reg 10 32bit mmio: [d7000000, d7ffffff]
PCI: 0000:01:05.0 reg 10 32bit mmio: [d8000000, d8ffffff]
PCI: 0000:01:05.1 reg 10 32bit mmio: [d9000000, d9ffffff]
PCI: 0000:01:05.2 reg 10 32bit mmio: [da000000, daffffff]
PCI: 0000:01:05.4 reg 10 32bit mmio: [db000000, dbffffff]
pci 0000:00:1e.0: transparent bridge
PCI: bridge 0000:00:1e.0 io port: [c000, cfff]
PCI: bridge 0000:00:1e.0 32bit mmio: [ce000000, dcdfffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 83, should
be 74 [20080609]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 20 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
tracer: 772 pages allocated for 65536 entries of 48 bytes
actual entries 65620
ACPI: RTC can wake from S4
system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
system 00:08: ioport range 0x290-0x297 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x480-0x4bf has been reserved
system 00:09: ioport range 0x900-0x91f has been reserved
system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:09: iomem range 0xfed50000-0xfed8ffff has been reserved
system 00:09: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0d: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:11: iomem range 0xffc00000-0xffefffff has been reserved
system 00:12: iomem range 0xf0000000-0xf3ffffff has been reserved
system 00:13: iomem range 0x0-0x9ffff could not be reserved
system 00:13: iomem range 0xc0000-0xdffff could not be reserved
system 00:13: iomem range 0xe0000-0xfffff could not be reserved
system 00:13: iomem range 0x100000-0xc7ffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:03
pci 0000:00:01.0: IO window: 0xe000-0xefff
pci 0000:00:01.0: MEM window: 0xdcf00000-0xdeffffff
pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000efffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: 0xd000-0xdfff
pci 0000:00:1c.0: MEM window: 0xdce00000-0xdcefffff
pci 0000:00:1c.0: PREFETCH window: 0x000000dff00000-0x000000dfffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1e.0: IO window: 0xc000-0xcfff
pci 0000:00:1e.0: MEM window: 0xce000000-0xdcdfffff
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 03 index 0 io port: [e000, efff]
bus: 03 index 1 mmio: [dcf00000, deffffff]
bus: 03 index 2 mmio: [e0000000, efffffff]
bus: 03 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [d000, dfff]
bus: 02 index 1 mmio: [dce00000, dcefffff]
bus: 02 index 2 mmio: [dff00000, dfffffff]
bus: 02 index 3 mmio: [0, 0]
bus: 01 index 0 io port: [c000, cfff]
bus: 01 index 1 mmio: [ce000000, dcdfffff]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 io port: [0, ffff]
bus: 01 index 4 mmio: [0, ffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 3483k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
type=2000 audit(1225366752.351:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1471
SELinux: Registering netfilter hooks
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:03:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT C7FAE0C0, 0214 (r1 AMI CPU1PM 1 INTL 20060113)
processor ACPI0007:00: registered as cooling_device0
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: SSDT C7FAE2E0, 0143 (r1 AMI CPU2PM 1 INTL 20060113)
processor ACPI0007:01: registered as cooling_device1
ACPI: Processor [CPU2] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0e: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0f: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata_piix 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xb800 ctl 0xb400 bmdma 0xa400 irq 23
ata4: SATA max UDMA/133 cmd 0xb000 ctl 0xa800 bmdma 0xa408 irq 23
ata3.00: ATA-8: Hitachi HDP725032GLA360, GM3OA52A, max UDMA/133
ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.01: ATAPI: HL-DT-STDVD-ROM GDRH20N, 0L02, max UDMA/100
ata3.00: configured for UDMA/133
ata3.01: configured for UDMA/100
ata4.00: ATA-8: Hitachi HDP725032GLA360, GM3OA52A, max UDMA/133
ata4.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA Hitachi HDP72503 GM3O PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg0 type 0
scsi 2:0:1:0: CD-ROM HL-DT-ST DVD-ROM GDRH20N 0L02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:1:0: Attached scsi CD-ROM sr0
sr 2:0:1:0: Attached scsi generic sg1 type 5
scsi 3:0:0:0: Direct-Access ATA Hitachi HDP72503 GM3O PQ: 0 ANSI: 5
sd 3:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 3:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg2 type 0
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xcdfff800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.4-58.fc10.i686 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27.4-58.fc10.i686 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00009400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27.4-58.fc10.i686 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00009800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27.4-58.fc10.i686 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000a000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27.4-58.fc10.i686 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input3
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised:
dm-devel@xxxxxxxxxx
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Magic number: 12:577:682
Freeing unused kernel memory: 360k freed
Write protecting the kernel text: 2856k
Write protecting the kernel read-only data: 1204k
input: PS/2 Logitech Mouse as /devices/platform/i8042/serio1/input/input4
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: 8192 avtab hash slots, 106629 rules.
SELinux: 8192 avtab hash slots, 106629 rules.
SELinux: 8 users, 11 roles, 2469 types, 119 bools, 1 sens, 1024 cats
SELinux: 73 classes, 106629 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses
genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1225366757.929:2): policy loaded auid=4294967295
ses=4294967295
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
ppdev: user-space parallel port driver
input: PC Speaker as /devices/platform/pcspkr/input/input5
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: no MSI. Back to INTx.
eth0: RTL8168c/8111c at 0xf083e000, 00:1e:8c:e1:be:b8, XID 3c2000c0 IRQ 16
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 23 (level, low) -> IRQ 23
intel_rng: FWH not detected
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Linux video capture interface: v2.00
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
HDA Intel 0000:00:1b.0: setting latency timer to 64
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
cx88[0]: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39,autodetected],
frontend(s): 1
cx88[0]: TV tuner type 4, Radio tuner type -1
cx2388x alsa driver version 0.0.6 loaded
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
cx88[0]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:01:00.2: PCI INT A -> GSI 16 (level, low) -> IRQ
16
cx88[0]/2: found at 0000:01:00.2, rev: 5, irq: 16, latency: 64, mmio:
0xcf000000
cx8802_probe() allocating 1 frontend(s)
cx88[1]: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39,autodetected],
frontend(s): 1
cx88[1]: TV tuner type 4, Radio tuner type -1
cx88[1]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:01:01.2: PCI INT A -> GSI 17 (level, low) -> IRQ
17
cx88[1]/2: found at 0000:01:01.2, rev: 5, irq: 17, latency: 64, mmio:
0xd1000000
cx8802_probe() allocating 1 frontend(s)
cx8800 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
cx88[0]/0: found at 0000:01:00.0, rev: 5, irq: 16, latency: 64, mmio:
0xce000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[2]: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39,autodetected],
frontend(s): 1
cx88[2]: TV tuner type 4, Radio tuner type -1
cx88[2]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:01:02.2: PCI INT A -> GSI 18 (level, low) -> IRQ
18
cx88[2]/2: found at 0000:01:02.2, rev: 5, irq: 18, latency: 64, mmio:
0xd3000000
cx8802_probe() allocating 1 frontend(s)
cx8800 0000:01:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
cx88[1]/0: found at 0000:01:01.0, rev: 5, irq: 17, latency: 64, mmio:
0xd0000000
cx88[1]/0: registered device video1 [v4l2]
cx88[1]/0: registered device vbi1
cx88[3]: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39,autodetected],
frontend(s): 1
cx88[3]: TV tuner type 4, Radio tuner type -1
cx88[3]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:01:03.2: PCI INT A -> GSI 20 (level, low) -> IRQ
20
cx88[3]/2: found at 0000:01:03.2, rev: 5, irq: 20, latency: 64, mmio:
0xd5000000
cx8802_probe() allocating 1 frontend(s)
cx8800 0000:01:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
cx88[2]/0: found at 0000:01:02.0, rev: 5, irq: 18, latency: 64, mmio:
0xd2000000
cx88[2]/0: registered device video2 [v4l2]
cx88[2]/0: registered device vbi2
cx88[4]: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39,autodetected],
frontend(s): 1
cx88[4]: TV tuner type 4, Radio tuner type -1
cx88[4]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:01:04.2: PCI INT A -> GSI 21 (level, low) -> IRQ
21
cx88[4]/2: found at 0000:01:04.2, rev: 5, irq: 21, latency: 64, mmio:
0xd7000000
cx8802_probe() allocating 1 frontend(s)
cx8800 0000:01:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
cx88[3]/0: found at 0000:01:03.0, rev: 5, irq: 20, latency: 64, mmio:
0xd4000000
cx88[3]/0: registered device video3 [v4l2]
cx88[3]/0: registered device vbi3
cx8800 0000:01:04.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
cx88[4]/0: found at 0000:01:04.0, rev: 5, irq: 21, latency: 64, mmio:
0xd6000000
cx88[4]/0: registered device video4 [v4l2]
cx88[4]/0: registered device vbi4
cx88[5]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2
[card=69,autodetected], frontend(s): 1
cx88[5]: TV tuner type -1, Radio tuner type -1
tveeprom 6-0050: Hauppauge model 69100, rev B2C3, serial# 3002110
tveeprom 6-0050: MAC address is 00-0D-FE-2D-CE-FE
tveeprom 6-0050: tuner model is Conexant CX24118A (idx 123, type 4)
tveeprom 6-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 6-0050: audio processor is None (idx 0)
tveeprom 6-0050: decoder processor is CX882 (idx 25)
tveeprom 6-0050: has no radio, has IR receiver, has no IR transmitter
cx88[5]: hauppauge eeprom: model=69100
input: cx88 IR (Hauppauge WinTV-HVR400 as
/devices/pci0000:00/0000:00:1e.0/0000:01:05.2/input/input6
cx88[5]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:01:05.2: PCI INT A -> GSI 22 (level, low) -> IRQ
22
cx88[5]/2: found at 0000:01:05.2, rev: 5, irq: 22, latency: 64, mmio:
0xda000000
cx8802_probe() allocating 1 frontend(s)
cx88_audio 0000:01:05.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22
cx88[5]/1: CX88x/0: ALSA support for cx2388x boards
cx8800 0000:01:05.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
cx88[5]/0: found at 0000:01:05.0, rev: 5, irq: 22, latency: 64, mmio:
0xd8000000
cx88[5]/0: registered device video5 [v4l2]
cx88[5]/0: registered device vbi5
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39]
cx88[0]/2: cx2388x based DVB/ATSC card
CX24123: detected CX24123
DVB: registering new adapter (cx88[0])
DVB: registering adapter 0 frontend 0 (Conexant CX24123/CX24109)...
cx88[1]/2: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39]
cx88[1]/2: cx2388x based DVB/ATSC card
CX24123: detected CX24123
DVB: registering new adapter (cx88[1])
DVB: registering adapter 1 frontend 0 (Conexant CX24123/CX24109)...
cx88[2]/2: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39]
cx88[2]/2: cx2388x based DVB/ATSC card
CX24123: detected CX24123
DVB: registering new adapter (cx88[2])
DVB: registering adapter 2 frontend 0 (Conexant CX24123/CX24109)...
cx88[3]/2: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39]
cx88[3]/2: cx2388x based DVB/ATSC card
CX24123: detected CX24123
DVB: registering new adapter (cx88[3])
DVB: registering adapter 3 frontend 0 (Conexant CX24123/CX24109)...
cx88[4]/2: subsystem: 17de:08b2, board: KWorld DVB-S 100 [card=39]
cx88[4]/2: cx2388x based DVB/ATSC card
CX24123: detected CX24123
DVB: registering new adapter (cx88[4])
DVB: registering adapter 4 frontend 0 (Conexant CX24123/CX24109)...
cx88[5]/2: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2
[card=69]
cx88[5]/2: cx2388x based DVB/ATSC card
DVB: registering new adapter (cx88[5])
DVB: registering adapter 5 frontend 0 (Conexant CX24116/CX24118)...
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1
extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
firmware: requesting intel-ucode/06-17-06
firmware: requesting intel-ucode/06-17-06
microcode: CPU0 updated from revision 0x0 to 0x60b, date = 01192008
microcode: CPU1 updated from revision 0x0 to 0x60b, date = 01192008
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
r8169: eth0: link up
r8169: eth0: link up
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
eth0: no IPv6 routers present
tun0: Disabled Privacy Extensions
Module Size Used by
tun 13444 1
sunrpc 155924 3
ip6t_REJECT 7296 2
nf_conntrack_ipv6 15864 2
ip6table_filter 6400 1
ip6_tables 14736 1 ip6table_filter
ipv6 230132 36 ip6t_REJECT,nf_conntrack_ipv6
cpufreq_ondemand 9996 1
acpi_cpufreq 11660 1
dm_multipath 17164 0
isl6421 5760 1
cx24116 17160 1
cx24123 15880 5
cx88_dvb 23812 0
cx88_vp3054_i2c 6272 1 cx88_dvb
tuner 24644 0
cx8800 30420 0
cx88_alsa 13704 0
cx8802 17412 1 cx88_dvb
cx88xx 66728 4 cx88_dvb,cx8800,cx88_alsa,cx8802
ir_common 41988 1 cx88xx
snd_hda_intel 350996 0
i2c_algo_bit 8836 2 cx88_vp3054_i2c,cx88xx
snd_seq_dummy 6660 0
videobuf_dvb 9860 3 cx88_dvb,cx8802,cx88xx
dvb_core 75880 2 cx88_dvb,videobuf_dvb
videodev 32128 3 tuner,cx8800,cx88xx
snd_seq_oss 30364 0
snd_seq_midi_event 9600 1 snd_seq_oss
snd_seq 48576 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
v4l1_compat 15492 1 videodev
snd_seq_device 10124 3 snd_seq_dummy,snd_seq_oss,snd_seq
compat_ioctl32 5120 1 cx8800
snd_pcm_oss 42496 0
snd_mixer_oss 16896 1 snd_pcm_oss
snd_pcm 65924 3 cx88_alsa,snd_hda_intel,snd_pcm_oss
tveeprom 14596 1 cx88xx
v4l2_common 13440 2 tuner,cx8800
snd_timer 22024 2 snd_seq,snd_pcm
snd_page_alloc 11016 2 snd_hda_intel,snd_pcm
videobuf_dma_sg 13828 5 cx88_dvb,cx8800,cx88_alsa,cx8802,cx88xx
snd_hwdep 10500 1 snd_hda_intel
snd 50616 11
cx88_alsa,snd_hda_intel,snd_seq_dummy,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_hwdep
videobuf_core 18052 5
cx8800,cx8802,cx88xx,videobuf_dvb,videobuf_dma_sg
iTCO_wdt 13732 0
iTCO_vendor_support 6916 1 iTCO_wdt
soundcore 9416 1 snd
i2c_i801 12048 0
i2c_core 21396 10
isl6421,cx24116,cx24123,cx88_vp3054_i2c,tuner,cx88xx,i2c_algo_bit,tveeprom,v4l2_common,i2c_i801
btcx_risc 7560 4 cx8800,cx88_alsa,cx8802,cx88xx
r8169 28548 0
pcspkr 6272 0
ppdev 10372 0
parport_pc 25620 0
parport 31956 2 ppdev,parport_pc
floppy 51988 0
ata_generic 8452 0
pata_acpi 7680 0
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
Subsystem: ASUSTeK Computer Inc. Device 817a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:01.0 PCI bridge: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: dcf00000-deffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: ASUSTeK Computer Inc. Device 817a
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable-
Address: 00000000 Data: 0000
Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x16, ASPM L0s, Latency L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 0, PowerLimit 75.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport-driver
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8290
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at cdff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: dce00000-dcefffff
Prefetchable memory behind bridge: 00000000dff00000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 8179
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 9000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 9400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 9800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at cdfff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ce000000-dcdfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 8179
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: ata_piix
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 23
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at a800 [size=4]
Region 4: I/O ports at a400 [size=16]
Region 5: Memory at cdfffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8179
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 23
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: KWorld Computer Co. Ltd. KWorld DVB-S 100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ce000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800
01:00.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: KWorld Computer Co. Ltd. Device 08b2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at cf000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx88-mpeg driver manager
Kernel modules: cx8802
01:01.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: KWorld Computer Co. Ltd. KWorld DVB-S 100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800
01:01.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: KWorld Computer Co. Ltd. Device 08b2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx88-mpeg driver manager
Kernel modules: cx8802
01:02.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: KWorld Computer Co. Ltd. KWorld DVB-S 100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800
01:02.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: KWorld Computer Co. Ltd. Device 08b2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx88-mpeg driver manager
Kernel modules: cx8802
01:03.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: KWorld Computer Co. Ltd. KWorld DVB-S 100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800
01:03.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: KWorld Computer Co. Ltd. Device 08b2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d5000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx88-mpeg driver manager
Kernel modules: cx8802
01:04.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: KWorld Computer Co. Ltd. KWorld DVB-S 100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800
01:04.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: KWorld Computer Co. Ltd. Device 08b2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d7000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx88-mpeg driver manager
Kernel modules: cx8802
01:05.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: Hauppauge computer works Inc. Device 6906
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx8800
Kernel modules: cx8800
01:05.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
Subsystem: Hauppauge computer works Inc. Device 6906
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1000ns min, 63750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d9000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: cx88_audio
Kernel modules: cx88-alsa
01:05.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: Hauppauge computer works Inc. Device 6906
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at da000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: cx8802
01:05.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)
Subsystem: Hauppauge computer works Inc. Device 6906
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1500ns min, 63750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at db000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Device 82c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at d800 [size=256]
Region 2: Memory at dceff000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at dfff0000 (64-bit, prefetchable) [size=64K]
Expansion ROM at dcec0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Endpoint, MSI 01
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data <?>
Kernel driver in use: r8169
Kernel modules: r8169
03:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 LE] (rev a1) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at dd000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at dcfe0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <4us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Kernel modules: nvidiafb
MemTotal: 3243968 kB
MemFree: 3080128 kB
Buffers: 6840 kB
Cached: 60400 kB
SwapCached: 0 kB
Active: 58080 kB
Inactive: 47788 kB
HighTotal: 2489984 kB
HighFree: 2378172 kB
LowTotal: 753984 kB
LowFree: 701956 kB
SwapTotal: 2031608 kB
SwapFree: 2031608 kB
Dirty: 4 kB
Writeback: 0 kB
AnonPages: 38684 kB
Mapped: 16516 kB
Slab: 16124 kB
SReclaimable: 4368 kB
SUnreclaim: 11756 kB
PageTables: 1776 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 3653592 kB
Committed_AS: 236340 kB
VmallocTotal: 241656 kB
VmallocUsed: 109264 kB
VmallocChunk: 130584 kB
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 4096 kB
DirectMap4k: 8192 kB
DirectMap4M: 778240 kB
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
