Hello, There is a regression regarding this DVB-C card from the subject, which as it looks is not very new, but nobody noticed the problem. After bisecting I've found the commit which is responsible for this problem - that the card is not detected. By the way mercurial bisect was not very useful because some commits does not compile or load, so I had to "simulate" bisecting. Bad version: changeset: 7484:0b82bb67fb80 parent: 7482:4fcb2ce44347 parent: 7483:13244661a8df user: Mauro Carvalho Chehab <mchehab@xxxxxxxxxxxxx> date: Tue Apr 01 18:59:34 2008 -0300 summary: merge: http://linuxtv.org/hg/~mkrufky/tuner b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 21 (level, low) -> IRQ 22 DVB: registering new adapter (FlexCop Digital TV device) b2c2-flexcop: MAC address = 00:d0:d7:13:c4:e4 b2c2-flexcop: i2c master_xfer failed CX24123: cx24123_i2c_readreg: reg=0x0 (error=-121) CX24123: wrong demod revision: 87 b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: i2c master_xfer failed mt352_read_register: readreg error (reg=127, ret==-121) b2c2-flexcop: i2c master_xfer failed nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121) Unknown/Unsupported NXT chip: 00 00 00 00 00 b2c2-flexcop: i2c master_xfer failed lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121) b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: i2c master_xfer failed stv0297_readreg: readreg error (reg == 0x80, ret == -121) b2c2-flexcop: i2c master_xfer failed mt312_read: ret == -121 b2c2-flexcop: no frontend driver found for this B2C2/FlexCop adapter ACPI: PCI interrupt for device 0000:06:00.0 disabled Good version: changeset: 7483:13244661a8df parent: 7442:b7bb2b116cbb user: Michael Krufky <mkrufky@xxxxxxxxxxx> date: Sun Mar 30 13:00:45 2008 -0400 summary: tuner-simple: fix broken build dependency b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 21 (level, low) -> IRQ 22 DVB: registering new adapter (FlexCop Digital TV device) b2c2-flexcop: MAC address = 00:d0:d7:13:c4:e4 b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: i2c master_xfer failed mt352_read_register: readreg error (reg=127, ret==-121) b2c2-flexcop: i2c master_xfer failed nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121) Unknown/Unsupported NXT chip: 00 00 00 00 00 b2c2-flexcop: i2c master_xfer failed lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121) b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: found the stv0297 at i2c address: 0x1c DVB: registering frontend 0 (ST STV0297 DVB-C)... b2c2-flexcop: initialization of 'Cable2PC/CableStar 2 DVB-C' at the 'PCI' bus controlled by a 'FlexCopIIb' complete The changeset 7484:0b82bb67fb80 is rather big, but I'm just guessing that removing/integrating of this file with other flexcop files is the cause: linux/drivers/media/dvb/b2c2/stv0297_cs2.c Kernel version 2.6.23. Currently can't test with newer kernel on this computer. I can give more info if needed. Regards _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
