|
I have 2 x WinTV-HS-S2 DVB-S & a Nebula
DVB-T PCI adaptors. I am only getting the frontend on the DVB-T #modprobe -i cx88-dvb FATAL: Error inserting cx88_dvb (/lib/modules/2.6.26.1/kernel/drivers/media/video/cx88/cx88-dvb.ko): Unknown symbol in module, or unknown parameter (see dmesg) #dmesg Linux video capture interface: v2.00 cx88/0: cx2388x v4l2 driver version 0.0.6 loaded cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded bttv: driver version 0.9.17 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture PCI: Disallowing DAC for device 0000:00:0a.0 eth0: Tigon3 [partno(284685-003) rev 0105 PHY(5701)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:0f:20:d7:1d:2c eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[0] eth0: dma_rwctrl[76ff000f] dma_mask[32-bit] bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 3, latency: 32, mmio: 0xf9000000 bttv0: detected: Nebula Electronics DigiTV [card=104], PCI subsystem ID is 0071:0101 bttv0: using: Nebula Electronics DigiTV [card=104,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00ff00cb [init] bttv0: tuner absent bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 .. ok bttv0: add subdevice "dvb0" input: bttv IR (card=104) as /devices/pci0000:00/0000:00:09.0/input/input1 cx88[0]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69,autodetected] cx88[0]: TV tuner type -1, Radio tuner type -1 bt878: gave up waiting for init of module bttv. bt878: Unknown symbol bttv_read_gpio bt878: gave up waiting for init of module bttv. bt878: Unknown symbol bttv_write_gpio Filesystem "md4": Disabling barriers, not supported by the underlying device XFS mounting filesystem md4 Ending clean XFS mount for filesystem: md4 XFS mounting filesystem hde1 Ending clean XFS mount for filesystem: hde1 XFS mounting filesystem hdg1 Ending clean XFS mount for filesystem: hdg1 Adding 240888k swap on /dev/md2. Priority:-1 extents:1 across:240888k hda: UDMA/100 mode selected hdc: UDMA/100 mode selected hde: UDMA/100 mode selected hdg: UDMA/100 mode selected bt878: gave up waiting for init of module bttv. bt878: Unknown symbol bttv_gpio_enable tveeprom 2-0050: Hauppauge model 69100, rev B2C3, serial# 3247319 tveeprom 2-0050: MAC address is 00-0D-FE-31-8C-D7 tveeprom 2-0050: tuner model is Conexant CX24118A (idx 123, type 4) tveeprom 2-0050: TV standards ATSC/DVB Digital (eeprom 0x80) tveeprom 2-0050: audio processor is None (idx 0) tveeprom 2-0050: decoder processor is CX882 (idx 25) tveeprom 2-0050: has no radio, has IR receiver, has no IR transmitter cx88[0]: hauppauge eeprom: model=69100 input: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci0000:00/0000:00:0b.0/input/input2 cx88[0]/0: found at 0000:00:0b.0, rev: 5, irq: 10, latency: 32, mmio: 0xf5000000 cx88[0]/0: registered device video1 [v4l2] cx88[0]/0: registered device vbi1 cx88[0]/2: cx2388x 8802 Driver Manager cx88[0]/2: found at 0000:00:0b.2, rev: 5, irq: 10, latency: 32, mmio: 0xf3000000 udev: renamed network interface eth0 to eth1 cx88[1]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69,autodetected] cx88[1]: TV tuner type -1, Radio tuner type -1 tveeprom 3-0050: Hauppauge model 69100, rev B2C3, serial# 3247400 tveeprom 3-0050: MAC address is 00-0D-FE-31-8D-28 tveeprom 3-0050: tuner model is Conexant CX24118A (idx 123, type 4) tveeprom 3-0050: TV standards ATSC/DVB Digital (eeprom 0x80) tveeprom 3-0050: audio processor is None (idx 0) tveeprom 3-0050: decoder processor is CX882 (idx 25) tveeprom 3-0050: has no radio, has IR receiver, has no IR transmitter cx88[1]: hauppauge eeprom: model=69100 input: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci0000:00/0000:00:0d.0/input/input3 cx88[1]/0: found at 0000:00:0d.0, rev: 5, irq: 3, latency: 32, mmio: 0xf0000000 cx88[1]/0: registered device video2 [v4l2] cx88[1]/0: registered device vbi2 cx88[1]/2: cx2388x 8802 Driver Manager cx88[1]/2: found at 0000:00:0d.2, rev: 5, irq: 3, latency: 32, mmio: 0xee000000 bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). bt878_probe: card id=[0x1010071],[ Nebula Electronics DigiTV ] has DVB functions. bt878(0): Bt878 (rev 17) at 00:09.1, irq: 3, latency: 32, memory: 0xf8800000 DVB: registering new adapter (bttv0) cx88_dvb: Unknown parameter `frontend' DVB: registering frontend 0 (NxtWave NXT6000 DVB-T)... cx88_dvb: Unknown parameter `frontend' |
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
