Hello,
have a problem when receiving the radio stations in the cable, the
sound is constantly being torn apart. Used Cinergy 1200 DVB-C:
##############################
00:0 a.0 multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: TERRATEC Electronic GmbH Unknown device 1176
Control: I / O Mem + + BusMaster Spec Cycle
MemWINV-VGASnoop-ParErr-Stepping-SERR-FastB2B -
Status: Cap-66MHz-UDF FastB2B + ParErr-DEVSEL = medium>
TAbort-<TAbort-<MAbort-> SERR-<PERR -
Latency: 32 (3750ns min, 9500ns max)
Interrupt: A pin routed to IRQ 21
Region 0: Memory at e0001000 (32-bit, non-prefetchable) [size = 512]
##############################
This problem has been fixed times:
http://www.mail-archive.com/linux-dvb @ linuxtv.org/msg26731.html
So here's my log:
#############################
saa7146: saa7146_register_extension (): ext: dc9bfde0
saa7146: register extension 'budget_av'.
saa7146: saa7146_init_one (): pci: db929c00
ACPI: PCI interrupt 0000:00:0 a.0 [A] -> GSI 18 (level, low) -> IRQ 21
saa7146: found saa7146 @ mem dc9aa000 (revision 1, irq 21) (0x153b, 0x1176).
saa7146 (1): dma buffer size 1347584
DVB: registering new adapter (Terratec Cinergy 1200 DVB-C MK3)
saa7146: saa7146_i2c_adapter_prepare (): bitrate: 0x00000000
saa7146: saa7146_i2c_reset (): error_state detected. Status: 0x00000400
saa7146: saa7146_i2c_transfer (): msg: 1 / 2
saa7146: saa7146_i2c_transfer (): msg: 2 / 2
saa7146: saa7146_i2c_writeout (): before: 0xa0cca1ec (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xa0cca1ec
saa7146: saa7146_i2c_writeout (): before: 0xc9da63a8 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xffffffa8
saa7146: saa7146_i2c_writeout (): before: 0xcf86dca8 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xffffffa8
saa7146: saa7146_i2c_writeout (): before: 0x040000a8 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xffffffa8
saa7146: saa7146_i2c_writeout (): before: 0x000000a8 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xffffffa8
saa7146: saa7146_i2c_writeout (): before: 0x000094a8 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xffffffa8
saa7146: saa7146_i2c_writeout (): before: 0x60c9daa8 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xffffffa8
saa7146: saa7146_i2c_writeout (): before: 0xf4ff0090 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xffffff90
saa7146: saa7146_i2c_transfer (): transmission successful. (msg: 2).
Adapter failed MAC signature check
MAC encoded from EEPROM was ff: ff: ff: ff: ff: ff: ff: ff: ff: ff:
ff: ff: ff: ff: ff: ff: ff: ff: ff: ff
saa7146: saa7146_i2c_transfer (): msg: 1 / 1
saa7146: saa7146_i2c_writeout (): before: 0x4a0108e4 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): i2c unexpected status 0021
saa7146: saa7146_i2c_writeout (): error in address phase.
saa7146: saa7146_i2c_transfer (): msg: 1 / 2
saa7146: saa7146_i2c_transfer (): msg: 2 / 2
saa7146: saa7146_i2c_reset (): busy_state detected.
saa7146: saa7146_i2c_reset (): error_state detected. Status: 0x00000042
saa7146: saa7146_i2c_writeout (): before: 0xa030a1ec (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0xa030a1ec
saa7146: saa7146_i2c_writeout (): before: 0x000000a8 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0x000aaca8
saa7146: saa7146_i2c_writeout (): before: 0x000000a4 (status: 0x00000000), 0
saa7146: saa7146_i2c_writeout (): after: 0x113b22a4
saa7146: saa7146_i2c_transfer (): transmission successful. (msg: 2).
KNC1-2: MAC addr = 00:0 a: ac: 11:3 b: 22
saa7146: saa7146_i2c_transfer (): msg: 1 / 2
saa7146: saa7146_i2c_transfer (): msg: 2 / 2
saa7146: saa7146_i2c_reset (): error_state detected. Status: 0x00000000
saa7146: saa7146_i2c_writeout (): before: 0xa0ffa1ec (status: 0x00000700), 0
saa7146: saa7146_i2c_writeout (): after: 0xa0ffa1ec
saa7146: saa7146_i2c_writeout (): before: 0xc9000040 (status: 0x00000700), 0
saa7146: saa7146_i2c_writeout (): after: 0xffffa140
saa7146: saa7146_i2c_transfer (): transmission successful. (msg: 2).
saa7146: saa7146_i2c_transfer (): msg: 1 / 1
saa7146: saa7146_i2c_writeout (): before: 0x180033e4 (status: 0x00000700), 0
saa7146: saa7146_i2c_writeout (): after: 0x180033e4
saa7146: saa7146_i2c_transfer (): transmission successful. (msg: 1).
..........
............
saa7146: saa7146_i2c_reset (): error_state detected. Status: 0x00000742
saa7146: saa7146_i2c_writeout (): before: 0xaa0000c0 (status: 0x00000700), 0
saa7146: saa7146_i2c_writeout (): i2c unexpected status 0721
saa7146: saa7146_i2c_writeout (): error in address phase.
saa7146: saa7146_i2c_transfer (): msg: 1 / 1
saa7146: saa7146_i2c_reset (): busy_state detected.
saa7146: saa7146_i2c_reset (): error_state detected. Status: 0x00000742
saa7146: saa7146_i2c_writeout (): before: 0xac0000c0 (status: 0x00000700), 0
saa7146: saa7146_i2c_writeout (): i2c unexpected status 0721
saa7146: saa7146_i2c_writeout (): error in address phase.
saa7146: saa7146_i2c_transfer (): msg: 1 / 1
saa7146: saa7146_i2c_reset (): busy_state detected.
saa7146: saa7146_i2c_reset (): error_state detected. Status: 0x00000742
saa7146: saa7146_i2c_writeout (): before: 0xae0000c0 (status: 0x00000700), 0
saa7146: saa7146_i2c_writeout (): i2c unexpected status 0721
saa7146: saa7146_i2c_writeout (): error in address phase.
it87: Found IT8705F chip at 0x290, revision 2
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@xxxxxxxxxx
kjournald starting. Commit interval 5 seconds
FS EXT3 on hdd1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
...........
...........
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): before:
0xd018d1ec (status: 0x00000000), 0
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): after: 0xd018d1ec
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): before:
0x00000040 (status: 0x00000000), 0
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): after: 0x5318d140
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_transfer ():
transmission successful. (msg: 2).
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_transfer (): msg: 1 / 2
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_transfer (): msg: 2 / 2
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): before:
0xd01bd1ec (status: 0x00000000), 0
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): after: 0xd01bd1ec
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): before:
0x00000040 (status: 0x00000000), 0
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): after: 0x001bd140
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_transfer ():
transmission successful. (msg: 2).
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_wait_for_debi_done_sleep
(): saa7146 (1): saa7146_wait_for_debi_done_sleep timed out while
waiting for transfer completion
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_transfer (): msg: 1 / 2
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_transfer (): msg: 2 / 2
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): before:
0xd018d1ec (status: 0x00000000), 0
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): after: 0xd018d1ec
Aug 7 15:24:54 vdr kernel: saa7146: saa7146_i2c_writeout (): before:
0x00000040 (status: 0x00000000), 0
.................
............
##############################
My system:
Debian Etch
Kernel 2.6.24.4
Cinergy 1200 DVB-C
S2300 TT V 2.3 "modded" (With Full-TS-Mod)
Can there was?
Thank you.
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
