Hi Community I am struggling to enjoy DVB-T on my AverTV E506 PCMCIA card. It seams I'm doing something terribly wrong but I cannot find the solution on my own. I am grateful for any help provided. What I did so far: I'm running Gentoo with a 2.6.24-r8 kernel on my Centrino Laptop. I have selected "Video for Linux" (nothing else, no cards, no frontends, no chips..) as a module in my kernel configuration and compiled the "v4l-dvb" drivers from the mercurial repository. I also have obtained the (hopefully) correct firmware for my card. Well when I plug the PCMCIA device in this is what dmesg shows me: pccard: CardBus card inserted into slot 1 PCI: Enabling device 0000:04:00.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5 saa7133[0]: found at 0000:04:00.0, rev: 209, irq: 5, latency: 0, mmio: 0x98000000 PCI: Setting latency timer of device 0000:04:00.0 to 64 saa7133[0]: subsystem: 1461:f436, board: AVerMedia Cardbus TV/Radio (E506R) [card=136,autodetected] saa7133[0]: board init: gpio is 220000 tuner' 5-0061: chip found @ 0xc2 (saa7133[0]) saa7133[0]: i2c eeprom 00: 61 14 36 f4 00 00 00 00 00 00 00 00 00 00 00 00 saa7133[0]: i2c eeprom 10: 00 ff e2 0e ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 02 02 01 01 03 08 ff 00 ff ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff 65 00 ff c2 1e ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff xc2028 5-0061: creating new instance xc2028 5-0061: type set to XCeive xc2028/xc3028 tuner xc2028 5-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7 xc2028 5-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. (0), id 00000000000000ff: xc2028 5-0061: Loading firmware for type=(0), id 0000000100000007. SCODE (20000000), id 0000000100000007: xc2028 5-0061: Loading SCODE for type=MONO SCODE HAS_IF_5320 (60008000), id 0000000800000007. saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 saa7133[0]: registered device radio0 Analog TV works with this setup, but I have no signs of DVB-T. No /dev/dvb devices are created although the module for the Zarlink tuner "mt352" is autoloaded when the card is inserted. Apparently I'm missing something. Any hints? Best regards Luke _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
