Hi,
a view days ago I bought a dvb-USB stick from Hauppauge (WinTV Nova T).
I want to use this stick with linux, but I sill have some trubble.
After a google-search it is clear, that the correct driver is dib0700,
and the firmware to use is dvb-usb-dib0700-1.10.fw (md5:
5878ebfcba2d8deb90b9120eb89b02da)
Kernel is 2.6.25
lsusb:
2040:7070 Hauppauge
If I want to tune to a channel (e.g. with kaffine) the dmesg-log is
overcrowed with "DiB0070 I2C write failed" and there is no sucessfull
tuning. The output of kaffeine while searching a channel is:
Using DVB device 0:0 "DiBcom 7000PC"
tuning DVB-T to 402000000 Hz
inv:2 bw:0 fecH:9 fecL:9 mod:6 tm:2 gi:4 hier:4
. LOCKED.
Transponders: 1/63
Invalid section length or timeout: pid=17
Frontend closed
Using DVB device 0:0 "DiBcom 7000PC"
tuning DVB-T to 410000000 Hz
inv:2 bw:0 fecH:9 fecL:9 mod:6 tm:2 gi:4 hier:4
. LOCKED.
Transponders: 2/63
Invalid section length or timeout: pid=17
.... <and so on>
The output of dmesg while attaching the stick and searching with
kaffeine and debug enabled is:
usb 1-6: new high speed USB device using ehci_hcd and address 6
usb 1-6: configuration #1 chosen from 1 choice
dvb-usb: found a 'Hauppauge Nova-T Stick' in cold state, will try to
load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
i2c-adapter i2c-0: SMBus Quick command not supported, can't probe for chips
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
DVB: registering new adapter (Hauppauge Nova-T Stick)
i2c-adapter i2c-1: SMBus Quick command not supported, can't probe for chips
DVB: registering frontend 0 (DiBcom 7000PC)...
DiB0070: Revision: 3
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070: CTRL_LO5: 0x16a4
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C read failed
DiB0070 I2C write failed
DiB0070: WBDStart = 0 (Vargen) - FF = 0
DiB0070: successfully identified
input: IR-receiver inside an USB DVB receiver as /class/input/input11
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.
usb 1-6: New USB device found, idVendor=2040, idProduct=7070
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: Product: Nova-T Stick
usb 1-6: Manufacturer: Hauppauge
usb 1-6: SerialNumber: 4030980792
DiB0070: Tuning for Band: 2 (402000 kHz)
DiB0070 I2C write failed
DiB0070 I2C read failed
DiB0070 I2C write failed
DiB0070: HFDIV code: 5
DiB0070: VCO = 1
DiB0070: VCOF in kHz: 4824000 ((6*402000) << 1))
DiB0070: REFDIV: 1, FREF: 12000
DiB0070: FBDIV: 67, Rest: 0
DiB0070: Num: 0, Den: 1, SD: 0
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C write failed
DiB0070 I2C read failed
DiB0070: CAPTRIM=64; ADC = 0 (ADC) & 0mV
DiB0070: CAPTRIM=64 is closer to target (400/3000)
DiB0070 I2C write failed
DiB0070 I2C read failed
DiB0070: CAPTRIM=96; ADC = 0 (ADC) & 0mV
<and so on...>
Here some more information about the stick:
lsusb -vvvv:
Bus 001 Device 006: ID 2040:7070 Hauppauge
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x2040 Hauppauge
idProduct 0x7070
bcdDevice 1.00
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 46
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
can't get device qualifier: Operation not permitted
can't get debug descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)
Thanks for your assistance. If you need any further informations or
tests, please let me know.
Best regards
Robert
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
