Hello, I installed the latest drivers and the video device works fine, only the ir receiver seems to be recognized but doesn't work. The driver creates the corresponding event device node but when using cat /dev/input/eventX there's no data received when pressing the rc keys. As far as I understood the ir receiver events should be mapped to keyboard events, means pressing the '1' on the remote should be like pressing the '1' on the keyboard. Doesn't work either. Do I miss something or is the ir receiver currently not supported? There's also a bttv card installed and the remote works in Windows, btw ... Thanks & Regards Peter Driver: 7402 Firmware: 4.95 $> cat /proc/version Linux version 2.6.22-14-rt (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP PREEMPT RT Tue Feb 12 09:57:10 UTC 2008 $> dmesg ... Linux video capture interface: v2.00 parport_pc 00:03: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, dma 0 bttv: driver version 0.9.17 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 18 bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 18, latency: 32, mmio: 0xdfdfe000 bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb bttv0: using: Hauppauge (bt878) [card=10,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] af9015_usb_probe: interface:0 af9015_identify_state: reply:02 dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (Afatech AF9015 DVB-T USB2.0 stick) af9015_eeprom_dump: tveeprom 1-0050: Hauppauge model 44804, rev C148, serial# 3976927 tveeprom 1-0050: tuner model is LG TP18PSB11D (idx 48, type 29) tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04) tveeprom 1-0050: audio processor is None (idx 0) tveeprom 1-0050: has no radio bttv0: Hauppauge eeprom indicates model#44804 bttv0: tuner type=29 bttv0: i2c: checking for MSP34xx @ 0x80... not found bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... 00: 2d 57 9f 0b 00 00 00 00 a4 15 16 90 00 02 01 02 not found 10: 03 80 00 fa fa 10 40 ef 01 30 31 30 31 30 31 31 20: 30 30 37 30 30 30 30 31 ff ff ff ff ff ff ff ff 30: 00 00 3a 01 00 08 02 00 1d 8d c4 04 82 ff ff ff 40: ff ff ff ff ff 08 02 00 1d 8d c4 04 82 ff ff ff 50: ff ff ff ff ff 24 00 00 04 03 09 04 14 03 47 00 60: 65 00 6e 00 69 00 61 00 74 00 65 00 63 00 68 00 70: 10 03 44 00 56 00 42 00 2d 00 54 00 20 00 32 00 80: 20 03 30 00 31 00 30 00 31 00 30 00 31 00 30 00 90: 31 00 30 00 36 00 30 00 30 00 30 00 30 00 31 00 a0: 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tuner' 1-0061: chip found @ 0xc2 (bt878 #0 [sw]) tuner-simple 1-0061: creating new instance tuner-simple 1-0061: type set to 29 (LG PAL_BG (TPI8PSB11D)) e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 .f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff af9015_read_config: xtal:2 set adc_clock:28000 .af9015_read_config: IF1:36125 af9015_read_config: MT2060 IF1:1220 af9015_read_config: tuner id1:130 af9015_read_config: spectral inversion:0 ok ACPI: PCI Interrupt 0000:00:0b.1[A] -> GSI 19 (level, low) -> IRQ 18 af9013: firmware version:4.65.0 DVB: registering frontend 0 (Afatech AF9013 DVB-T)... af9015_tuner_attach: af9015_set_gpio: gpio:3 gpioval:03 ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 19 MT2060: successfully identified (IF1 = 1220) dvb-usb: Afatech AF9015 DVB-T USB2.0 stick successfully initialized and connected. af9015_init: af9015_init_endpoint: USB speed:3 af9015_download_ir_table: usbcore: registered new interface driver dvb_usb_af9015 ... $> cat /proc/bus/input/devices ... I: Bus=0003 Vendor=15a4 Product=9016 Version=0101 N: Name="Geniatech DVB-T 2" P: Phys=usb-0000:00:10.3-4/input1 S: Sysfs=/class/input/input1 U: Uniq=010101010600001 H: Handlers=kbd event1 B: EV=120003 B: KEY=10000 7 ff87207a c14057ff febeffdf ffefffff ffffffff fffffffe B: LED=7 ... $> ls /dev/input/by-id/ ... usb-Geniatech_DVB-T_2_010101010600001-event-ir -> ../event1 ... _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
