Timo Fager wrote: > Hi, > > This is regarding a previous thread concerning Terratec Cinergy C PCI: > > http://marc.info/?l=linux-dvb&m=120059268408703&w=2 > > I also purchased the Terratec Cinergy C PCI card, and installed > the mantis driver, but to my surprise it didn't recognize the > card at all. The reason turned out to be that the PCI ID is > just a bit different (0x4c35 instead of 0x4e35) > > lspci -vvn: > > 00:0f.0 0480: 1822:4c35 (rev 01) > Subsystem: 153b:1178 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR+ <PERR+ > Latency: 64 (2000ns min, 63250ns max) > Interrupt: pin A routed to IRQ 5 > Region 0: Memory at cddff000 (32-bit, prefetchable) [size=4K] > > Then I was courageous enough to simply change the ID in the source code. > This caused the whole computer to hang immediately after inserting the > module. > However, during bootup the driver actually tried to recognize the card, > with these results: > > kern.log: > > Mar 12 21:00:23 hawk kernel: [ 51.359517] ACPI: PCI Interrupt 0000:00:0f.0[A] > -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 > Mar 12 21:00:23 hawk kernel: [ 51.366388] irq: 5, latency: 64 > Mar 12 21:00:23 hawk kernel: [ 51.366391] memory: 0xcddff000, mmio: > 0xf8864000 > Mar 12 21:00:23 hawk kernel: [ 51.366398] found a VP-2040 PCI DVB-C device > on (00:0f.0), > Mar 12 21:00:23 hawk kernel: [ 51.366404] Mantis Rev 1 [153b:1178], > irq: 5, latency: 64 > Mar 12 21:00:23 hawk kernel: [ 51.366410] memory: 0xcddff000, mmio: > 0xf8864000 > Mar 12 21:00:23 hawk kernel: [ 51.432789] MAC > Address=[ff:ff:ff:ff:ff:ff] > Mar 12 21:00:23 hawk kernel: [ 51.432926] mantis_alloc_buffers (0): > DMA=0x33f10000 cpu=0xf3f10000 size=65536 > Mar 12 21:00:23 hawk kernel: [ 51.432937] mantis_alloc_buffers (0): > RISC=0x33ef9000 cpu=0xf3ef9000 size=1000 > Mar 12 21:00:23 hawk kernel: [ 51.432945] DVB: registering new adapter > (Mantis dvb adapter) > Mar 12 21:00:23 hawk kernel: [ 51.895885] input: PC Speaker as > /class/input/input5 > Mar 12 21:00:23 hawk kernel: [ 51.949954] mantis_frontend_init (0): > Probing for CU1216 (DVB-C) > Mar 12 21:00:23 hawk kernel: [ 51.952061] mantis_frontend_init (0): !!! NO > Frontends found !!! > > The frontend, however, didn't match. At this point I don't easily see a > solution, > do you have any suggestions? Is it possible that there's another version of > the card with different components? I can look for product codes in the card > if > that is helpful. > Does manually attaching the TDA10021 frontend help, instead of the TDA10023 ? (in mantis_dvb.c) Regards, Manu _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
