dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
Because I remember with 72e that with GPIO6 set to 1 the tunner is disabled.
Anyway, your dmesg should tell more information after the failed tunning.
Albert
2008/3/18, Antti Luoma <anluoma@xxxxxxxxx>:
Good morning to everyone,
I tested the Stick with windows and it found channels ok.. So what shall I do next?
-antti-2008/3/18, Antti Luoma <anluoma@xxxxxxxxx>:Hi,
Tested with same results :( (no channels...)
Tomorrow I'l (hmm today, its getting late) test this with windows that it works in there...
-Antti-2008/3/18, Albert Comerma <albert.comerma@xxxxxxxxx>:Just as I pointed a few hours ago;
If you speak french you can have a look here;
http://www.louviaux.com-a.googlepages.com/tntpinnaclepctvdvb-t72e
Or if you don't you can go the fast way;
wget http://www.barbak.org/v4l_for_72e_dongle.tar.bz2
tar xvjf v4l_for_72e_dongle.tar.bz2
cd v4l-dvb
sudo cp firmware/dvb-usb-dib0700-1.10.fw /lib/firmware/
make all
sudo make install
That should work for you. Please let me know.2008/3/17, Antti Luoma <anluoma@xxxxxxxxx>:Hi,_______________________________________________
I have trying to get Solo Stick (72e) to work for couple of days, but with no luck. So what's the current status of this driver?
I did download latest drivers from mercurial today, added PCI_ids for card, modified dib0700_devices.c (in stk7070p_frontend_attach), added device to struct dvb_usb_device_properties dib0700_devices[] where stk7070p_frontend_attach was called.
After that it looked promising:
usb 6-4: new high speed USB device using ehci_hcd and address 30
[ 6722.607546] usb 6-4: configuration #1 chosen from 1 choice
[ 6722.607622] dvb-usb: found a 'Pinnacle PCTV 72e DVB-T' in warm state.
[ 6722.607648] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 6722.607724] DVB: registering new adapter (Pinnacle PCTV 72e DVB-T)
[ 6722.731734] dvb_register_frontend
[ 6722.731742] DVB: registering frontend 0 (DiBcom 7000PC)...
[ 6722.811550] DiB0070: successfully identified
[ 6722.811557] dvb-usb: Pinnacle PCTV 72e DVB-T successfully initialized and connected.
BUT if I do a scan I don't get channels (i checked that I have correct frequencies):
#scan -o vdr fi-Eurajoki
scanning fi-Eurajoki
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
initial transponder 610000000 0 2 9 3 1 2 0
initial transponder 666000000 0 2 9 3 1 2 0
initial transponder 722000000 0 2 9 3 1 2 0
>>> tune to: 610000:I999B8C23D999M64T8G8Y0:T:27500:
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
>>> tune to: 666000:I999B8C23D999M64T8G8Y0:T:27500:
__tune_to_transponder:1483: ERROR: Setting frontend parameters failed: 19 No such device
>>> tune to: 666000:I999B8C23D999M64T8G8Y0:T:27500:
__tune_to_transponder:1483: ERROR: Setting frontend parameters failed: 19 No such device
>>> tune to: 722000:I999B8C23D999M64T8G8Y0:T:27500:
__tune_to_transponder:1483: ERROR: Setting frontend parameters failed: 19 No such device
>>> tune to: 722000:I999B8C23D999M64T8G8Y0:T:27500:
__tune_to_transponder:1483: ERROR: Setting frontend parameters failed: 19 No such device
dumping lists (0 services)
Done.
Any thoughts??
--
-Antti-
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
--
-Antti-
--
-Antti-
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
