I have just received the driver source (v0.0.2) for the Freecom DVB-T USB device with usb id 14aa:0160 from Realtek. The bug in v0.0.1 seems to be fixed. I can now tune to channels and watch TV (tested with Kaffeine). dmesg output: usb 3-1: USB disconnect, address 3 usb 5-5: new high speed USB device using ehci_hcd and address 9 usb 5-5: new device found, idVendor=14aa, idProduct=0160 usb 5-5: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 5-5: Product: DTV Receiver usb 5-5: Manufacturer: DTV Receiver usb 5-5: SerialNumber: 0000000000039537 usb 5-5: configuration #1 chosen from 1 choice dvb-usb: found a 'Freecom USB 2.0 DVB-T Device' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (Freecom USB 2.0 DVB-T Device) +rtd2831u_fe_attach -rtd2831u_fe_attach DVB: registering frontend 0 (Realtek RTD2830 DVB-T)... input: IR-receiver inside an USB DVB receiver as /class/input/input7 dvb-usb: schedule remote query interval to 300 msecs. dvb-usb: Freecom USB 2.0 DVB-T Device successfully initialized and connected. and some output while scanning for channels: + ########################## rtd2830_init: 441: init once v.0.0.2 #####################################################TD2831_RMAP_INDEX_USB_STAT=0x3 HIGH SPEED #####################################################RTD2831_RMAP_INDEX_SYS_GPO=0x10 #####################################################RTD2831_RMAP_INDEX_SYS_GPO=0x1 #####################################################RTD2831_RMAP_INDEX_SYS_GPO=0x5 This device has the MT2060 onboard..... CDevice::MT2060TunerInit -- begin MT2060_Open -- Start MT2060_Open:MT_NO_ERROR -->MT2060_ReInit MT2060_ReInit -- start MT2060_ReInit:Initialize the tuner state. MT2060_ReInit:Write the default values to each of the tuner registers ******************** read time = 1 ****************** MT2060_Open -- end MT2060_SetParam MT2060_SetGainRange CDevice::MT2060TunerInit -- end ###################rtd2830_general_init: rtd2830_general_init : demod know tuner type MT2060 rtd2830_general_init - rtd2830_init rtd2830_get_tune_settings: Do Nothing + rtd2830_set_parameters CDevice::SetMT2060Tuner -- begin MT2060_ChangeFreq -- start f_in = 786000000, f_IF1 = 1220000000, f_out = 36125000, f_IFBW = 8750000Round_fLO MT_ResetExclZones MT_AvoidSpurs status = 0ofLO1=1871000000, ofLO2=1176250000, pInfo->reg[LO_STATUS]=8 status1 = 0 status2 = 0 status3 = 0 status = 0, reg[LO1_1] = 0xffstatus4 = 0 Write LO1C_1 register MT2060_ChangeFreq -- end CDevice::SetMT2060Tuner -- end +rtd2830_soft_reset -rtd2830_soft_reset rtd2830_scan_channel_procedure : *****SIGNAL_LOCK***** - rtd2830_set_parameters rtd2830_read_status ******FSM = 11****** rtd2830_read_status ******FSM = 11****** rtd2830_read_status ******FSM = 11****** rtd2830_read_status ******FSM = 11****** ... As you can see it does find the correct tuner chip now. Driver source can be downloaded from http://www.megaupload.com/?d=DPE2C8I5 Instructions on how to build the driver can be found in the Doc/ directory. Have fun. Andy _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
