This is and update on the issue - it turned out that I do not get enough current so that I
can tune and drive the rotor. On both Windows and Linux side my LNBs drain about
150 mA when connected to the Twinhan VP1041. The rotor needs about 300 mA to
move. So on the Windows side I measured about 440-450 mA when the dish was
moving (not including a short burst at the beginning of the dish drive). But on the Linux side
I don't seem to be able to go above 300 mA. No clue why ....
Does anyone know if the max current is controlled in some way on this cards?
Thanks in advance!
can tune and drive the rotor. On both Windows and Linux side my LNBs drain about
150 mA when connected to the Twinhan VP1041. The rotor needs about 300 mA to
move. So on the Windows side I measured about 440-450 mA when the dish was
moving (not including a short burst at the beginning of the dish drive). But on the Linux side
I don't seem to be able to go above 300 mA. No clue why ....
Does anyone know if the max current is controlled in some way on this cards?
Thanks in advance!
----- Original Message ----
From: Придворов Андрей <ua0lnj@xxxxx>
To: linux-dvb <linux-dvb@xxxxxxxxxxx>
Sent: Monday, February 11, 2008 3:45:02 PM
Subject: Re: [linux-dvb] mantis vp1041 with strange diseqc rotor commands
-----Inline Attachment Follows-----
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
From: Придворов Андрей <ua0lnj@xxxxx>
To: linux-dvb <linux-dvb@xxxxxxxxxxx>
Sent: Monday, February 11, 2008 3:45:02 PM
Subject: Re: [linux-dvb] mantis vp1041 with strange diseqc rotor commands
I think, this is becouse "Initial support for Mantis VP-1041"
not usability yet.
I use patch from Hans Werner for 1041, works better.
----- Original Message -----From: Simeon SimeonovTo: linux-dvbSent: Tuesday, February 12, 2008 6:47 AMSubject: mantis vp1041 with strange diseqc rotor commandsHi,
I am using the latest mantis drivers from Manu's repository:
http://jusst.de/hg/mantis/
with my Azureware twinhan vp1041 based card.
Locking to DVB-S channels works fine almost all the time with the patched szap or patched mythtv.
Did not try DVB-S2 yet. But what I am having troubles now is the diseqc. I have a switch behind a diseqc 1.2 rotor (goto stored positions).
The switching works fine under Windoz. I have no problems also using it with my other card in the same box - Twinhan 102g.
Initially with the vp1041 card after a couple of diseqc commands I would get stb0899_diseqc_fifo_empy timeout. It turned out that I had to use some very long pauses before sending a repeat command. If
for the 102g standart 15ms worked fine, for the vp1041 I had to use 1s! pause. Then the rotor will start
moving very slowly with small steps - as if it is does one step , stops and then continues to the desired position.If one is patient enough the rotor gets to the desired position. I checked using voltmeter the voltages that come out of the card and they seem to be good. For sending the commands I used both mythtv and hacked version of Michel Verbraak's gotox program.
Has anyone experienced something similar with stb0899 frontend? Perhaps you can give me an idea what might be going wrong?
Thanks,
Simeon
____________________________________________________________________________________
Be a better friend, newshound, and
know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
-----Inline Attachment Follows-----
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Looking for last minute shopping deals? Find them fast with Yahoo! Search.
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
