Hi! I don't know if I succeeded sending the mail below earlier so I send it again.. I have also been trying almost every patch available on the net today without any good result. I have also downloaded the firmware again and I have checked my channels.conf against en.kingofsat.net/hdtv.php If I'm using the patch from 2007-12-15 to enable HVR4000 support in the multiproto tree, which szap should I use to be able to szap to DVB-S2 channels? Maybe I'm using a szap that can't tune to DVB-S2-channels? I don't know if it matters anymore, but my HD channels are on my second port on my Diseqc. /Lars -- Previous mail: Now I've been trying a little again, but with the same bad result :( I patched with this new patch from 2007-12-15 instead. make clean; make distclean reboot make all; make install reboot lsmod: Module Size Used by lirc_mceusb2 12356 1 lirc_dev 13816 1 lirc_mceusb2 nvidia 8888772 36 cx88_dvb 16328 0 cx88_vp3054_i2c 4672 1 cx88_dvb cx8802 17860 1 cx88_dvb cx88xx 65124 2 cx88_dvb,cx8802 ir_common 33540 1 cx88xx tveeprom 18448 1 cx88xx videodev 27136 1 cx88xx v4l2_common 19264 2 cx88xx,videodev v4l1_compat 13188 1 videodev btcx_risc 6088 2 cx8802,cx88xx video_buf_dvb 7108 1 cx88_dvb dvb_core 83824 1 video_buf_dvb video_buf 23108 4 cx88_dvb,cx8802,cx88xx,video_buf_dvb cx24116 17168 1 isl6421 4096 1 ./scan2 -t 2 "SVT HD" reading channels from file '/root/.szap/channels.conf' zapping to 3 'SVT HD': sat 1, frequency = 11421 MHz H, symbolrate 25000000, vpid = 0x0200, apid = 0x0280 sid = 0x0ed9 (fec = -2147483648, mod = 2) Querying info .. Delivery system=DVB-S2 using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' ----------------------------------> Using 'Conexant CX24116/CX24118' DVB-S diseqc: sat_no:1 pol_vert:0 hi_band:0 cmd:e0 10 38 f6 wait:0 do_tune: API version=2, delivery system = 2 do_tune: Frequency = 1671000, Srate = 25000000 (DVB-S2) do_tune: Frequency = 1671000, Srate = 25000000 (SET_PARAMS) status 03 | signal d0c0 | snr 0000 | ber 00000000 | unc 00000000 | ... status 01 | signal d0c0 | snr 0000 | ber 00000000 | unc 00000000 | dmesg: cx24116_firmware_ondemand: Waiting for firmware upload (dvb-fe-cx24116.fw)... cx24116_firmware_ondemand: Waiting for firmware upload(2)... cx24116_load_firmware: FW version 1.20.79.0 cx24116_firmware_ondemand: Firmware upload complete dvb_frontend_ioctl: DVBFE_GET_INFO dvb_frontend_ioctl: FESTATE_RETUNE: fepriv->state=2 dvb_frontend_ioctl: DVBFE_GET_INFO dvb_frontend_ioctl: FESTATE_RETUNE: fepriv->state=2 I still get the same result. I have a quite old firmware I think, has anything changed in it the last months? Thanks for the help! Best Regards, Lars Fredriksson On Mon, Dec 31, 2007 at 02:08:59PM +0300, Igor wrote: > > > This is what I've done: > > > > Downloaded the latest hg from http://jusst.de/hg/multiproto > > OK > > > > Patched it with this patch: > > http://www.mail-archive.com/linux-dvb@xxxxxxxxxxx/msg28003/multiproto-hvr4k.patch.bz2 > > > please, use latest version from 15.12.2007 > http://www.mail-archive.com/linux-dvb@xxxxxxxxxxx/msg28020.html > > > make all; make install > > please, try to restart after make install > > > > Igor > _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ----- End forwarded message ----- _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
