hello, I've just put two of these card in my machine, and seem to run into the tuner issue described at http://www.linuxtv.org/wiki/index.php/TerraTec_Cinergy_1200_DVB-S_budget/Typhoon/KNC1_DVB-S_budget has anybody gotten these cards to work ? any pointers on how to get tuning to work ? I'm new to dvb-driver development, suggestions on how to get started are welcome too below are lspci output, dmesg output and scan output : DMESG saa7146: register extension 'budget_av'. PCI: Setting latency timer of device 0000:00:10.1 to 64 ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 ACPI: PCI Interrupt 0000:04:08.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16 saa7146: found saa7146 @ mem ffffc20010606000 (revision 1, irq 16) (0x1894,0x0016). saa7146 (0): dma buffer size 192512 DVB: registering new adapter (KNC TV STAR DVB-S) adapter failed MAC signature check encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff KNC1-0: MAC addr = 00:09:d6:65:9d:14 DVB: registering frontend 0 (ST STV0299 DVB-S)... budget-av: ci interface initialised. ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 ACPI: PCI Interrupt 0000:04:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17 saa7146: found saa7146 @ mem ffffc2001061c000 (revision 1, irq 17) (0x1894,0x0016). saa7146 (1): dma buffer size 192512 DVB: registering new adapter (KNC TV STAR DVB-S) saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer Couldn't read from EEPROM: not there? saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer KNC1-1: Could not read MAC from KNC1 card DVB: registering frontend 1 (ST STV0299 DVB-S)... budget-av: ci interface initialised. budget-av: cam inserted B saa7146: register extension 'dvb'. dvb_ca adaptor 1: PC card did not respond :( not all of these messages seem positive, should I worry ? (there's no CAM in the CI-slot yet) LSPCI 04:08.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01) Subsystem: KNC One Unknown device 0016 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (3750ns min, 9500ns max) Interrupt: pin A routed to IRQ 16 Region 0: Memory at fdbfe000 (32-bit, non-prefetchable) [size=512] 04:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01) Subsystem: KNC One Unknown device 0016 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 32 (3750ns min, 9500ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at fdbfd000 (32-bit, non-prefetchable) [size=1K] SCAN silverstar:/home/myth # scan -vvv -a 1 /usr/share/dvb/dvb-s/Astra-19.2E scanning /usr/share/dvb/dvb-s/Astra-19.2E using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0' initial transponder 12551500 V 22000000 5 >>> >>> tune to: 12551:v:0:22000 DiSEqC: switch pos 0, 13V, hiband (index 2) diseqc_send_msg:56: DiSEqC: e0 10 38 f1 00 00 DVB-S IF freq is 1951500 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x03 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x03 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 WARNING: >>> tuning failed!!! >>> >>> tune to: 12551:v:0:22000 (tuning failed) DiSEqC: switch pos 0, 13V, hiband (index 2) diseqc_send_msg:56: DiSEqC: e0 10 38 f1 00 00 DVB-S IF freq is 1951500 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x01 >>> >>> tuning status == 0x01 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 >>> >>> tuning status == 0x02 WARNING: >>> tuning failed!!! ERROR: initial tuning failed dumping lists (0 services) Done. the signal from the satellite is fine, have been using a settop box for several months a Skystar 2 card in the same machine scanned successfully and gave access to the FTA channels I'm using OpenSUSE 10.3, kernel version 2.6.22.12, dvb archive 816f256c2973 (downloaded it yesterday) thanks, Luc _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
