Hello,
I just was about to add a TechniSat SkyStar 2 Rev 2.7V to my VDR-Server
which already has a Hauppauge Nexus 2.1 and a Nova-S.
Unfortunately the driver doesn't seem to recoginze the SkyStar correctly
and therefore no /dev/dvb/adapterX/... is created for this card.
The drivers I use are from the "MASTER v4l-dvb development repository"
of today (v4l-dvb-09fcd9084746).
The card is recogized by the system:
# lspci -v
05:01.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII
DVB chip / Technisat SkyStar2 DVB card (rev 02)
Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip /
Technisat SkyStar2 DVB card
Flags: slow devsel, IRQ 17
Memory at febf0000 (32-bit, non-prefetchable) [size=64K]
I/O ports at ec00 [size=32]
The following lines are probably the most interesting lines in syslog
when calling "make insmod":
Nov 7 15:50:48 core flexcop-pci: will use the HW PID filter.
Nov 7 15:50:48 core flexcop-pci: card revision 2
Nov 7 15:50:48 core ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 17
(level, low) -> IRQ 17
Nov 7 15:50:48 core DVB: registering new adapter (FlexCop Digital TV
device)
Nov 7 15:50:48 core b2c2-flexcop: MAC address = 00:d0:d7:13:b7:54
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core i2c-adapter i2c-4: SMBus Quick command not
supported, can't probe for chips
Nov 7 15:50:48 core b2c2-flexcop: i2c master_xfer failed
Nov 7 15:50:49 core b2c2-flexcop: i2c master_xfer failed
Nov 7 15:50:49 core b2c2-flexcop: i2c master_xfer failed
Nov 7 15:50:49 core mt352_read_register: readreg error (reg=127, ret==-121)
Nov 7 15:50:49 core b2c2-flexcop: i2c master_xfer failed
Nov 7 15:50:49 core nxt200x: nxt200x_readbytes: i2c read error (addr
0x0a, err == -121)
Nov 7 15:50:49 core Unknown/Unsupported NXT chip: 00 00 00 00 00
Nov 7 15:50:49 core b2c2-flexcop: i2c master_xfer failed
Nov 7 15:50:49 core lgdt330x: i2c_read_demod_bytes: addr 0x59 select
0x02 error (ret == -121)
Nov 7 15:50:49 core b2c2-flexcop: i2c master_xfer failed
Nov 7 15:50:49 core b2c2-flexcop: i2c master_xfer failed
Nov 7 15:50:49 core stv0297_readreg: readreg error (reg == 0x80, ret ==
-121)
Nov 7 15:50:49 core b2c2-flexcop: i2c master_xfer failed
Nov 7 15:50:49 core mt312_read: ret == -121
Nov 7 15:50:49 core b2c2-flexcop: no frontend driver found for this
B2C2/FlexCop adapter
Nov 7 15:50:49 core ACPI: PCI interrupt for device 0000:05:01.0 disabled
So my questions are: Is the SkyStar2 Rev 2.7V supposed to work with the
current dvb-drivers? If yes: Could you please give me some hints on
which drivers to load?
greetings, Alex
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
