Hi all, I have a weird problem with my dvb-t satelco easywatch mobile set. When I tune the card to a tv channel and receive the signal I get an irq overflow exactly every 30 seconds. The overflow is accompanied by picture and sound distortions and happens in a interval of exactly 30 seconds. It is a pcmcia card running with kernel 2.6.23 and the pluto2 module. Can anyone give some hints how to get rid of this annoying overflow ? Might it be a hardware problem with my laptop (hp nx6125). I opened a kernel bug report a while go without response http://bugzilla.kernel.org/show_bug.cgi?id=9162 Some logs included. ------------- cat /proc/interrupts CPU0 0: 3223542 local-APIC-edge timer 1: 3453 IO-APIC-edge i8042 8: 0 IO-APIC-edge rtc 12: 132 IO-APIC-edge i8042 14: 14935 IO-APIC-edge ide0 15: 28955 IO-APIC-edge ide1 17: 3 IO-APIC-fasteoi ATI IXP, ATI IXP Modem 19: 29565 IO-APIC-fasteoi ohci_hcd:usb1, ohci_hcd:usb2,ehci_hcd:usb3 20: 208802 IO-APIC-fasteoi yenta, pluto2 21: 447 IO-APIC-fasteoi acpi, firewire_ohci 22: 178374 IO-APIC-fasteoi ndiswrapper 23: 32045 IO-APIC-fasteoi eth0 NMI: 0 LOC: 3223433 ERR: 13 ----------------- dmesg pccard: card ejected from slot 0 pccard: CardBus card inserted into slot 0 PCI: Enabling device 0000:03:00.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:03:00.0 to 64 DVB: registering new adapter (pluto2) pluto2 0000:03:00.0: board revision 2.15 pluto2 0000:03:00.0: S/N 13320542100301 pluto2 0000:03:00.0: MAC 00:d0:16:03:bb:9c DVB: registering frontend 0 (Philips TDA10046H DVB-T)... tda1004x: setting up plls for 53MHz sampling clock tda1004x: timeout waiting for DSP ready tda1004x: found firmware revision 0 -- invalid tda1004x: trying to boot from eeprom tda1004x: timeout waiting for DSP ready tda1004x: found firmware revision 0 -- invalid tda1004x: waiting for firmware upload... tda1004x: found firmware revision 20 -- ok pluto2 0000:03:00.0: overflow irq (1) ------------------- tzap -c channels.conf XXX using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' reading channels from file 'channels.conf' .. .. .. status 00 | signal 9b9b | snr abab | ber 0001fffe | unc 00000000 | status 1f | signal 9c9c | snr fcfc | ber 0000011a | unc ffffffff | FE_HAS_LOCK status 1f | signal 9c9c | snr fefe | ber 0000005c | unc 00000000 | FE_HAS_LOCK status 1f | signal 9b9b | snr fefe | ber 00000072 | unc 00000000 | FE_HAS_LOCK status 1f | signal 9d9d | snr fefe | ber 00000078 | unc 00000000 | FE_HAS_LOCK ... ... -------------- /var/log/messages tda1004x: setting up plls for 53MHz sampling clock tda1004x: timeout waiting for DSP ready tda1004x: found firmware revision 0 -- invalid tda1004x: trying to boot from eeprom tda1004x: timeout waiting for DSP ready tda1004x: found firmware revision 0 -- invalid tda1004x: waiting for firmware upload... tda1004x: found firmware revision 20 -- ok pluto2 0000:03:00.0: overflow irq (1) ta1004x: setting up plls for 53MHz sampling clock tda1004x: found firmware revision 20 -- ok pluto2 0000:03:00.0: overflow irq (1) APIC error on CPU0: 40(40) pluto2 0000:03:00.0: overflow irq (1) pluto2 0000:03:00.0: overflow irq (1) Note the apic error seems unrelated as booting with noapic doesn't change anything. ----------------- lspci -vv: 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01) Subsystem: Hewlett-Packard Company MX6125 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: d0300000-d03fffff Prefetchable memory behind bridge: 00000000c0000000-00000000c7ffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [44] HyperTransport: MSI Mapping Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device 308b 00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=10, subordinate=10, sec-latency=0 I/O behind bridge: 00004000-00005fff Memory behind bridge: cc000000-cfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x16 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 2, PowerLimit 10.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd Off, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device 308b Capabilities: [b8] HyperTransport: MSI Mapping Capabilities: [100] Advanced Error Reporting 00:05.0 PCI bridge: ATI Technologies Inc Unknown device 5a37 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=20, subordinate=20, sec-latency=0 I/O behind bridge: 00002000-00003fff Memory behind bridge: c8000000-cbffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x16 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 3, PowerLimit 6.500000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd Off, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device 308b Capabilities: [b8] HyperTransport: MSI Mapping Capabilities: [100] Advanced Error Reporting 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at d0400000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at d0401000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at d0402000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11) Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Region 0: I/O ports at 8200 [size=16] Region 1: Memory at d0403000 (32-bit, non-prefetchable) [size=1K] Capabilities: [b0] HyperTransport: MSI Mapping 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI (prog-if 8a [Master SecP PriP]) Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 7010 [size=16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=02, subordinate=06, sec-latency=64 I/O behind bridge: 00001000-00001fff Memory behind bridge: d0000000-d02fffff Prefetchable memory behind bridge: 50000000-53ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- 00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 02) Subsystem: Hewlett-Packard Company MX6125 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min), Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at d0404000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:14.6 Modem: ATI Technologies Inc ATI SB400 - AC'97 Modem Controller (rev 02) (prog-if 00 [Generic]) Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min), Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at d0405000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 01:05.0 VGA compatible controller: ATI Technologies Inc ATI Radeon XPRESS 200M 5955 (PCIE) (prog-if 00 [VGA]) Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 255 (2000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 6000 [size=256] Region 2: Memory at d0300000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at d0320000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03) Subsystem: Hewlett-Packard Company MX6125 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (16000ns min) Interrupt: pin A routed to IRQ 23 Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable+ DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable- Address: ffef3ffffffff7f8 Data: ffff 02:02.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Hewlett-Packard Company MX6125 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin A routed to IRQ 22 Region 0: Memory at d0010000 (32-bit, non-prefetchable) [size=8K] 02:04.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller Subsystem: Hewlett-Packard Company MX6125 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at d0012000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: 50000000-53fff000 (prefetchable) Memory window 1: 54000000-57fff000 I/O window 0: 00001000-000010ff I/O window 1: 00001400-000014ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+ 16-bit legacy interface ports at 0001 02:04.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company MX6125 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 21 Region 0: Memory at d0013000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at d0014000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ 02:04.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller Subsystem: Hewlett-Packard Company MX6125 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 21 Region 0: Memory at d0018000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:04.4 Generic system peripheral [0805]: Texas Instruments PCI6411, PCI6421, PCI6611, PCI6621, PCI7411, PCI7421, PCI7611, PCI7621 Secure Digital (SD) Controller Subsystem: Hewlett-Packard Company MX6125 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 9 Region 0: Memory at d001a000 (32-bit, non-prefetchable) [size=256] Region 1: Memory at d001b000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at d001c000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 03:00.0 Multimedia video controller: SCM Microsystems, Inc. Pluto2 DVB-T Receiver for PCMCIA [EasyWatch MobilSet] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin A routed to IRQ 20 Region 0: Memory at 54000200 (32-bit, non-prefetchable) [size=128] Region 1: Memory at 54000000 (32-bit, non-prefetchable) [size=512] Capabilities: [78] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
