Hi people, I've got the latest DVICO Fusion HDTV Dual Express. From what I have gathered thus far, it has a Conexant cx23885 chipset and an xceive xc30xx chipset. I'm not sure whether it would work with the xc3028 driver, i have loaded the xc3028-fe patched module as according to steps outlined here: http://fremnet.net/article/228/dvico-fusionhdtv-dual-digital-4- under-linux but it has no effect. I actually have the dual digital 4 card referred to in that article running perfectly, but I'm not so naive as to think that my new card which is PCIe 1x will work, especially given the fact that I think it's a newer xceive chipset than that in the dual digital 4. I compiled the very latest v4l-dvb and got the cx23885 module loaded, it detects the card as an unknown type, as shown in the following dmesg output: [ 5980.021706] cx23885 driver version 0.0.1 loaded [ 5980.021770] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 17 [ 5980.021774] cx23885[0]: Your board isn't known (yet) to the driver. You can [ 5980.021776] cx23885[0]: try to pick one of the existing card configs via [ 5980.021777] cx23885[0]: card=<n> insmod option. Updating to the latest [ 5980.021778] cx23885[0]: version might help as well. [ 5980.021780] cx23885[0]: Here is a list of valid choices for the card=<n> insmod option: [ 5980.021782] cx23885[0]: card=0 -> UNKNOWN/GENERIC [ 5980.021784] cx23885[0]: card=1 -> Hauppauge WinTV-HVR1800lp [ 5980.021786] cx23885[0]: card=2 -> Hauppauge WinTV-HVR1800 [ 5980.021788] cx23885[0]: card=3 -> Hauppauge WinTV-HVR1250 [ 5980.021789] cx23885[0]: card=4 -> DViCO FusionHDTV5 Express [ 5980.021798] CORE cx23885[0]: subsystem: 18ac:db78, board: UNKNOWN/ GENERIC [card=0,autodetected] [ 5980.120888] cx23885[0]: i2c bus 0 registered [ 5980.120905] cx23885[0]: i2c bus 1 registered [ 5980.120919] cx23885[0]: i2c bus 2 registered [ 5980.147782] cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 17, latency: 0, mmio: 0xfd800000 [ 5980.147801] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 6178.439162] Linux video capture interface: v2.00 [ 6178.531298] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded [ 6279.216926] usbcore: registered new interface driver dvb_usb_cxusb Okay, so if I tell it that its card number 4, it registers the dvb adapter0 in /dev/dvb/adapter0 and so forth. However it loads the LG tuner chipset that ships with the HDTV5 Express card, so we definitely know that won't work. So to cut a long story short, reading the xceive chipset on the card it appears to say xc3008ACQ. This may not mean much to anybody, it doesnt to me. So realising this card does not have support under linux yet, I primarily would like to volunteer for testing of this card for anybody brave enough to endeavour to get this working. Thanks a lot, and I hope some of this made sense. This is the first time I've posted to any mailing list. Thanks guys, Patrick Claven _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
