Hi everyone, I'm trying to get a Hauppauge Nova-T stick working using Ubuntu 7.04. I have installed the latest cvs drivers (from 2007-10-10) and I'm using the newest firmware mentioned on the mailing list (dvb-usb-dib0700-1.10.fw), all to no avail. Scan gives me no channels even though I know channels exists (see below). Using a predefined channels.conf I'm able to use tzap to get a lock on a channel (see below). However, no matter what I do I am unable to get ANY output from /dev/dvb/adapter0/dvr0. cat /dev/dvb/adapter0/dvr0 > test.mpg (while tzap -r is "running") will give me a zero sized file. Any suggestions? Is this a bug? Ole /dev/dvb/adapter0: -------- ls -la /dev/dvb/adapter0/ total 0 drwxr-xr-x 2 root root 120 2007-10-11 19:57 . drwxr-xr-x 3 root root 60 2007-10-11 19:57 .. crw-rw---- 1 root video 212, 4 2007-10-11 19:57 demux0 crw-rw---- 1 root video 212, 5 2007-10-11 19:57 dvr0 crw-rw---- 1 root video 212, 3 2007-10-11 19:57 frontend0 crw-rw---- 1 root video 212, 7 2007-10-11 19:57 net0 tzap output: -------- tzap -r DR2 using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' tuning to 714000000 Hz video pid 0x00d3, audio pid 0x00dd status 0b | signal 234e | snr 0000 | ber 001fffff | unc 00000000 | status 1b | signal 21e5 | snr 0000 | ber 001fffff | unc 00000000 | FE_HAS_LOCK status 1b | signal 2174 | snr 0000 | ber 001fffff | unc 00000000 | FE_HAS_LOCK status 1b | signal 21f5 | snr 0000 | ber 001fffff | unc 00000000 | FE_HAS_LOCK channels.conf: -------- DR2:714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_AUTO:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:211:221:102 scan output: -------- scan .kde/share/apps/kaffeine/dvb-t/dk-CPH scanning .kde/share/apps/kaffeine/dvb-t/dk-CPH using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 714000000 0 2 9 3 1 3 0 >>> tune to: 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 dumping lists (0 services) Done. /lib/firmware: -------- ls -la /lib/firmware/ total 88 drwxr-xr-x 4 root root 4096 2007-10-11 19:51 . drwxr-xr-x 16 root root 4096 2007-10-11 00:27 .. drwxr-xr-x 4 root root 4096 2007-04-15 13:53 2.6.20-15-generic drwxr-xr-x 4 root root 4096 2007-10-11 00:28 2.6.20-16-generic lrwxrwxrwx 1 root root 23 2007-10-11 19:51 dvb-usb-dib0700-03-pre1.fw -> dvb-usb-dib0700-1.10.fw -rw-r--r-- 1 root root 33277 2007-10-11 00:33 dvb-usb-dib0700-03-pre1.fw.org -rw-r--r-- 1 root root 34306 2007-09-10 11:09 dvb-usb-dib0700-1.10.fw dmesg output: -------- [ 15.016000] dib0700: loaded with support for 5 different device-types [ 15.048000] ath_pci: 0.9.4.5 (0.9.3.1) [ 15.052000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 16 [ 15.052000] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 15.500000] dvb-usb: found a 'Hauppauge Nova-T Stick' in cold state, will try to load a firmware [ 15.584000] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-03-pre1.fw' [ 15.816000] dib0700: firmware started successfully. [ 15.844000] hda_codec: STAC922x, Apple subsys_id=106b0800 [ 16.320000] dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state. [ 16.320000] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 16.324000] DVB: registering new adapter (Hauppauge Nova-T Stick) [ 16.680000] DVB: registering frontend 0 (DiBcom 7000PC)... [ 16.728000] MT2060: successfully identified (IF1 = 1220) [ 17.256000] input: IR-receiver inside an USB DVB receiver as /class/input/input7 [ 17.256000] dvb-usb: schedule remote query interval to 150 msecs. [ 17.256000] dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected. [ 17.260000] usbcore: registered new interface driver dvb_usb_dib0700 _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
