Hi, I've just bought a 2nd hand TwinHan VisionPlus (not sure of exact model, but it is a DVB-S card with a CI slot), but it is not being recognised by the dst module. The guy I bought it off had it working, but he's not contactable until next week, and he mentioned that a few settings and maybe a patch are going to be needed. I tried both the in-kernel modules from 2.6.22, and the source from hg. The last attempt with the hg sources resulted in the following messages (dst verbose=4): bttv: driver version 0.9.17 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:05:00.0, irq: 21, latency: 64, mmio: 0xdfefe000 bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00f500fd [init] bttv0: using tuner=4 bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:05:00.1[A] -> GSI 21 (level, low) -> IRQ 21 bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB functions. bt878(0): Bt878 (rev 17) at 05:00.1, irq: 21, latency: 64, memory: 0xdfeff000 dvb_bt8xx: identified card0 as bttv0 DVB: registering new adapter (bttv0). dst(0) rdc_8820_reset: Resetting DST dst(0) dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 06 00 00 00 00 00 fa ] dst(0) write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x00) dst(0) dst_error_recovery: Trying to return from previous errors. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x00) dst(0) dst_error_recovery: Trying to return from previous errors. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) write_dst: RDC 8820 RESET dst(0) dst_error_bailout: Trying to bailout from previous error. dst(0) rdc_8820_reset: Resetting DST dst(0) dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_probe: unknown device. frontend_init: Could not find a Twinhan DST. dvb-bt8xx: A frontend driver was not found for device 109e/0878 subsystem 1822/0001 This is the only bttv card in the machine, but there are a pair of FlexCopII's installed (and working fine). Can anyone suggest anything I can try, or any debugging I can turn on to help? _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
