Quoting Michael Krufky <mkrufky@xxxxxxxxxxx>: > This looks like the FX2 usb controller is in an unstable state... > First, try a > cold reboot. If that doesnt help, then boot into windows and give it a quick > test, then warm boot back into linux. If that still doesnt help, > please let me > know. Well, bad news and slightly less bad news. The bad news: a cold boot had the same result. The dmesg output: [ 34.337117] check for warm 1660 932 [ 34.337121] something went very wrong, device was not found in current device list - let's see what comes next. [ 34.337124] check for cold fe9 d500 [ 34.337126] check for warm fe9 d501 [ 34.337128] something went very wrong, device was not found in current device list - let's see what comes next. [ 34.337131] check for cold fe9 db50 [ 34.337132] check for warm fe9 db51 [ 34.337134] check for cold fe9 db54 [ 34.337136] check for warm fe9 db55 [ 34.337138] check for cold fe9 db58 [ 34.337140] check for warm fe9 db59 [ 34.337141] something went very wrong, device was not found in current device list - let's see what comes next. [ 34.337144] check for cold fe9 db00 [ 34.337146] check for warm fe9 db01 [ 34.337147] something went very wrong, device was not found in current device list - let's see what comes next. [ 34.337150] check for cold fe9 db10 [ 34.337152] check for warm fe9 db11 [ 34.337154] something went very wrong, device was not found in current device list - let's see what comes next. [ 34.337156] check for warm fe9 db78 [ 34.337158] check for warm fe9 db70 [ 34.337160] dvb-usb: found a 'DViCO FusionHDTV DVB-T NANO2' in warm state. [ 34.337173] power control: 1 [ 34.337175] >>> de 00 [ 34.337178] dvb-usb: bulk message failed: -22 (2/0) [ 34.337235] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 34.337407] all in all I will use 40960 bytes for streaming [ 34.337409] allocating buffer 0 [ 34.337419] buffer 0: ffff81003223a000 (dma: 841195520) [ 34.337421] allocating buffer 1 [ 34.337430] buffer 1: ffff810031858000 (dma: 830832640) [ 34.337432] allocating buffer 2 [ 34.337439] buffer 2: ffff810031842000 (dma: 830742528) [ 34.337441] allocating buffer 3 [ 34.337449] buffer 3: ffff81003229e000 (dma: 841605120) [ 34.337451] allocating buffer 4 [ 34.337459] buffer 4: ffff8100325ae000 (dma: 844816384) [ 34.337461] allocation successful [ 34.337467] DVB: registering new adapter (DViCO FusionHDTV DVB-T NANO2) [ 34.338098] >>> 51 [ 36.337886] dvb-usb: bulk message failed: -110 (1/0) [ 36.337893] >>> 05 fd 00 [ 38.334831] dvb-usb: bulk message failed: -110 (3/0) [ 38.478625] gpio_write failed. [ 38.478627] >>> 05 fd 02 [ 40.475720] dvb-usb: bulk message failed: -110 (3/0) [ 40.656584] >>> 09 01 01 0f 7f [ 42.656427] dvb-usb: bulk message failed: -110 (5/0) [ 42.656493] dvb-usb: no frontend was attached by 'DViCO FusionHDTV DVB-T NANO2' [ 42.656670] power control: 0 [ 42.656672] dvb-usb: DViCO FusionHDTV DVB-T NANO2 successfully initialized and connected. [ 42.656688] usbcore: registered new interface driver dvb_usb_cxusb A warm boot from Windows, however, resulted in success: [ 33.991423] check for warm 1660 932 [ 33.991427] something went very wrong, device was not found in current device list - let's see what comes next. [ 33.991430] check for cold fe9 d500 [ 33.991432] check for warm fe9 d501 [ 33.991434] something went very wrong, device was not found in current device list - let's see what comes next. [ 33.991436] check for cold fe9 db50 [ 33.991438] check for warm fe9 db51 [ 33.991440] check for cold fe9 db54 [ 33.991442] check for warm fe9 db55 [ 33.991443] check for cold fe9 db58 [ 33.991445] check for warm fe9 db59 [ 33.991447] something went very wrong, device was not found in current device list - let's see what comes next. [ 33.991450] check for cold fe9 db00 [ 33.991451] check for warm fe9 db01 [ 33.991453] something went very wrong, device was not found in current device list - let's see what comes next. [ 33.991456] check for cold fe9 db10 [ 33.991457] check for warm fe9 db11 [ 33.991459] something went very wrong, device was not found in current device list - let's see what comes next. [ 33.991462] check for warm fe9 db78 [ 33.991463] check for warm fe9 db70 [ 33.991466] dvb-usb: found a 'DViCO FusionHDTV DVB-T NANO2' in warm state. [ 33.991483] power control: 1 [ 33.991486] >>> de 00 [ 33.991621] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 34.022650] all in all I will use 40960 bytes for streaming [ 34.022655] allocating buffer 0 [ 34.022667] buffer 0: ffff810032ece000 (dma: 854384640) [ 34.022669] allocating buffer 1 [ 34.022678] buffer 1: ffff810032ee2000 (dma: 854466560) [ 34.022680] allocating buffer 2 [ 34.022689] buffer 2: ffff81003241a000 (dma: 843161600) [ 34.022691] allocating buffer 3 [ 34.022700] buffer 3: ffff810032f60000 (dma: 854982656) [ 34.022702] allocating buffer 4 [ 34.022710] buffer 4: ffff81003626a000 (dma: 908500992) [ 34.022712] allocation successful [ 34.022718] DVB: registering new adapter (DViCO FusionHDTV DVB-T NANO2) [ 34.023541] >>> 51 [ 34.023663] >>> 05 fd 00 [ 34.023888] <<< d9 [ 34.343458] >>> 05 fd 02 [ 34.344561] <<< db [ 34.624077] <<< 01 14 [ 34.624083] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)... [ 34.636468] ok [ 34.637412] input: bttv IR (card=34) as /class/input/input5 [ 34.700797] power control: 0 [ 34.700803] dvb-usb: DViCO FusionHDTV DVB-T NANO2 successfully initialized and connected. [ 34.700822] usbcore: registered new interface driver dvb_usb_cxusb The problem now is that nothing seems to be able to tune in a channel. (If this is off-topic here, please let me know.) The antenna connection is fine, since it works in Windows, and I have a correct channels.conf file for my area, but something's still not quite right. Scan output: adam@lawngnome:/tmp$ scan /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-Perth scanning /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-Perth using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 226500000 1 3 9 3 1 1 0 initial transponder 177500000 1 2 9 3 1 2 0 initial transponder 191625000 1 3 9 3 1 1 0 initial transponder 219500000 1 3 9 3 1 1 0 initial transponder 536625000 1 2 9 3 1 2 0 >>> tune to: >>> 226500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 226500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE (tuning >>> failed) WARNING: >>> tuning failed!!! >>> tune to: >>> 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE (tuning >>> failed) WARNING: >>> tuning failed!!! >>> tune to: >>> 191625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 191625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE (tuning >>> failed) WARNING: >>> tuning failed!!! >>> tune to: >>> 219500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 219500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE (tuning >>> failed) WARNING: >>> tuning failed!!! >>> tune to: >>> 536625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 536625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE (tuning >>> failed) WARNING: >>> tuning failed!!! ERROR: initial tuning failed dumping lists (0 services) Done. Running tzap shows: adam@lawngnome:/tmp$ tzap -c ~/.mplayer/channels.conf "7 Digital" -r using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' tuning to 177500000 Hz video pid 0x0301, audio pid 0x0302 status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | And so on. MPlayer seems to have the same issue. > BTW, Markus emailed you asking you to try his repository -- this > problem here is > with the usb controller, so trying his repository will not help you. I did try Markus's repository just for the sake of completeness, but the results are the same. Thanks, Adam _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
