May 2006 I went through pain to make this card work. I did get it working under FC4. Now it is time to upgrade.
Chose ubuntu 7.04 this time (installed a bigger disk in same box so I know everything works). FC4 is still available until I can make this new version work.
===
from lspci -vvv
=====
02:01.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: DViCO Corporation FusionHDTV DVB-T Dual Digital
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:01.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: DViCO Corporation Unknown device db50
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
=====
I have manually added
cx88_dvb
to /etc/modules
uname -a
Linux myth 2.6.20-16-generic #2 SMP Wed May 23 01:46:23 UTC 2007 i686 GNU/Linux
partial dmesg output:
[ 31.372109] dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in cold state, will try to load a firmware
[ 31.381966] cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
[ 31.382100] CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [card=44,autodetected]
[ 31.382106] TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
[ 31.432095] cx2388x v4l2 driver version 0.0.6 loaded
[ 31.575744] usb 4-4: USB disconnect, address 3
[ 31.615455] parport: PnPBIOS parport detected.
[ 31.615488] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 32.023840] dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw'
[ 32.023850] dvb-usb: could not stop the USB controller CPU.
[ 32.023856] dvb-usb: error while transferring firmware (transferred size: -19, block size: 10)
[ 32.023860] dvb-usb: firmware download failed at 15 with -22
[ 32.023881] dvb_usb_cxusb: probe of 4-4:1.0 failed with error -22
[ 32.151047] usbcore: registered new interface driver dvb_usb_cxusb
[ 32.554524] cx88[0]/2: cx2388x 8802 Driver Manager
[ 32.554559] ACPI: PCI Interrupt 0000:02:01.2[A] -> GSI 22 (level, low) -> IRQ 21
[ 32.554575] cx88[0]/2: found at 0000:02:01.2, rev: 5, irq: 21, latency: 64, mmio: 0xfd000000
[ 32.554766] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 21
[ 32.554780] cx88[0]/0: found at 0000:02:01.0, rev: 5, irq: 21, latency: 64, mmio: 0xfc000000
[ 32.554902] cx88[0]/0: registered device video0 [v4l2]
[ 32.554948] cx88[0]/0: registered device vbi0
[ 32.555767] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 22
[ 32.555816] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 32.822194] usb 4-4: new high speed USB device using ehci_hcd and address 4
[ 32.870123] intel8x0_measure_ac97_clock: measured 54105 usecs
[ 32.870127] intel8x0: clocking to 48000
[ 32.954554] usb 4-4: configuration #1 chosen from 1 choice
[ 33.071330] usbtest 4-4:1.0: FX2 device
[ 33.071337] usbtest 4-4:1.0: high speed {control bulk-in bulk-out} tests (+alt)
[ 33.071350] usbcore: registered new interface driver usbtest
[ 33.188448] fuse init (API version 7.8)
[ 33.223451] lp0: using parport0 (interrupt-driven).
[ 33.302665] cx2388x dvb driver version 0.0.6 loaded
[ 33.302673] cx8802_register_driver() ->registering driver type=dvb access=shared
[ 33.302679] CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [card=44]
[ 33.302685] cx88[0]/2: cx2388x based dvb card
[ 33.353012] DVB: registering new adapter (cx88[0]).
[ 33.353022] DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
=======
# ls -R /dev/dvb
/dev/dvb:
adapter0
/dev/dvb/adapter0:
demux0 dvr0 frontend0 net0
USB cable is attached to the card as required. Mythtv is operational and I can watch TV. I do not have a second tuner and my remote does not work.
Any ideas?
Thanks
Craig
Chose ubuntu 7.04 this time (installed a bigger disk in same box so I know everything works). FC4 is still available until I can make this new version work.
===
from lspci -vvv
=====
02:01.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: DViCO Corporation FusionHDTV DVB-T Dual Digital
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:01.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: DViCO Corporation Unknown device db50
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
=====
I have manually added
cx88_dvb
to /etc/modules
uname -a
Linux myth 2.6.20-16-generic #2 SMP Wed May 23 01:46:23 UTC 2007 i686 GNU/Linux
partial dmesg output:
[ 31.372109] dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in cold state, will try to load a firmware
[ 31.381966] cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
[ 31.382100] CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [card=44,autodetected]
[ 31.382106] TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
[ 31.432095] cx2388x v4l2 driver version 0.0.6 loaded
[ 31.575744] usb 4-4: USB disconnect, address 3
[ 31.615455] parport: PnPBIOS parport detected.
[ 31.615488] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 32.023840] dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw'
[ 32.023850] dvb-usb: could not stop the USB controller CPU.
[ 32.023856] dvb-usb: error while transferring firmware (transferred size: -19, block size: 10)
[ 32.023860] dvb-usb: firmware download failed at 15 with -22
[ 32.023881] dvb_usb_cxusb: probe of 4-4:1.0 failed with error -22
[ 32.151047] usbcore: registered new interface driver dvb_usb_cxusb
[ 32.554524] cx88[0]/2: cx2388x 8802 Driver Manager
[ 32.554559] ACPI: PCI Interrupt 0000:02:01.2[A] -> GSI 22 (level, low) -> IRQ 21
[ 32.554575] cx88[0]/2: found at 0000:02:01.2, rev: 5, irq: 21, latency: 64, mmio: 0xfd000000
[ 32.554766] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 21
[ 32.554780] cx88[0]/0: found at 0000:02:01.0, rev: 5, irq: 21, latency: 64, mmio: 0xfc000000
[ 32.554902] cx88[0]/0: registered device video0 [v4l2]
[ 32.554948] cx88[0]/0: registered device vbi0
[ 32.555767] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 22
[ 32.555816] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 32.822194] usb 4-4: new high speed USB device using ehci_hcd and address 4
[ 32.870123] intel8x0_measure_ac97_clock: measured 54105 usecs
[ 32.870127] intel8x0: clocking to 48000
[ 32.954554] usb 4-4: configuration #1 chosen from 1 choice
[ 33.071330] usbtest 4-4:1.0: FX2 device
[ 33.071337] usbtest 4-4:1.0: high speed {control bulk-in bulk-out} tests (+alt)
[ 33.071350] usbcore: registered new interface driver usbtest
[ 33.188448] fuse init (API version 7.8)
[ 33.223451] lp0: using parport0 (interrupt-driven).
[ 33.302665] cx2388x dvb driver version 0.0.6 loaded
[ 33.302673] cx8802_register_driver() ->registering driver type=dvb access=shared
[ 33.302679] CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [card=44]
[ 33.302685] cx88[0]/2: cx2388x based dvb card
[ 33.353012] DVB: registering new adapter (cx88[0]).
[ 33.353022] DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
=======
# ls -R /dev/dvb
/dev/dvb:
adapter0
/dev/dvb/adapter0:
demux0 dvr0 frontend0 net0
USB cable is attached to the card as required. Mythtv is operational and I can watch TV. I do not have a second tuner and my remote does not work.
Any ideas?
Thanks
Craig
Get the Yahoo! toolbar and be alerted to new email wherever you're surfing.
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
