Hi again!
I did like this:
Compiled my kernel without DVB and v4l
Compiled the drivers fro mthe HVR4000 tree and did a make install
insmodded dvb-core (and b2c2-flexcop-pci, budget, dvb-usb-nova-t-usb2 for my other cards) and cx88-dvb and it looks quite good in dmesg;
Linux video capture interface: v2.00
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=57,autodetected]
TV tuner 63 at 0x1fe, Radio tuner -1 at 0x1fe
tveeprom 5-0050: Hauppauge model 69009, rev B2D3, serial# 1705190
tveeprom 5-0050: MAC address is 00-0D-FE-1A-04-E6
tveeprom 5-0050: tuner model is Philips FMD1216MEX (idx 133, type 4)
tveeprom 5-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
tveeprom 5-0050: audio processor is CX882 (idx 33)
tveeprom 5-0050: decoder processor is CX882 (idx 25)
tveeprom 5-0050: has radio, has IR receiver, has no IR transmitter
cx88[0]: hauppauge eeprom: model=69009
input: cx88 IR (Hauppauge WinTV-HVR400 as /class/input/input7
cx88[0]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:00:0a.2[A] -> GSI 17 (level, low) -> IRQ 20
cx88[0]/2: found at 0000:00:0a.2, rev: 5, irq: 20, latency: 32, mmio: 0xdd000000
cx2388x dvb driver version 0.0.6 loaded
cx8802_register_driver() ->registering driver type=dvb access=shared
CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=57]
cx88[0]/2: cx2388x based dvb card
cx24116: cx24116_attach
DVB: registering new adapter (cx88[0]).
DVB: registering frontend 4 (Conexant CX24116/CX24118)...
I do only have the satellite input connected - is this adapter 4 the DVB-S part of the card? I tried to run a dvbscan but it failed - maybe I need a patched version
of dvbscan?
Best regards, Lars Fredriksson
On Wed, May 02, 2007 at 09:58:54PM +0200, Roland Mieslinger wrote:
> On Wed, 2007-05-02 at 21:10 +0200, Lars Fredriksson wrote:
> > Hi!
> >
> > I have a HVR4000 in yhe same computer as my other DVB-cards (that I'm using
> > together with Myth) - I compiled stoth's HVR4000-tree but I couldn't of
> > course insmod any modules because of a bunch unresolved symbols (I'm running
> > 2.6.20-rc5).
> >
> > If I still want to use my other DVB-cards with Myth and I would like to do
> > some testing with the HVR - how should I do? Can I use the HVR4000-tree for
> > all cards and together with Myth?
> >
> > Thanks for any help.
> >
> > /Lars
>
> I'm not developer, and haven't work with the HVR4000-tree, so this can
> be wrong or stupid.
>
> You can try 'make unload', that should remove all modules bulit within
> the tree (even if loaded from kernel).
>
> "make load" will load all modules.
>
> Roland
>
>
--
Bringing computers into the home won't change either one, but may
revitalize the corner saloon.
.___.__ __ .__
__| _/|__| ____ ____ _______/ |_|__|__ __ ____
/ __ | | |/ ___\_/ __ \ / ___/\ __\ \ \/ // __ \
/ /_/ | | / /_/ > ___/ \___ \ | | | |\ /\ ___/
\____ | |__\___ / \___ >____ > |__| |__| \_/ \___ >
\/ /_____/ \/ \/ \/
http://www.fredriksson.net/ :: http://digestive.mine.nu/
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
