Re: kworld atsc 110 remote

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello
   Yeah I have a modified patch that seems more responsive that
detects button presses
through gpio.  also the patch I found on the list (80th attempt....)
has some duplicate entries
in the key map that i think is causing some of the
problems(specifically presses being miss
detected as  other buttons.  so far (since last night) it seems
better. Though I'd like to use
lirc directly so any remote would work.  the lirc_i2c driver is very
similar to the saa7134's i2c
input driver, code wise , but I just get 1 byte codes like its hard
coded for there remote.
If the patch stays stable I'll post it.
                     later
                         Jonathan
On 4/2/07, Nathan Faust <nfaust@xxxxxxxxxxxxxxxxxxxxx> wrote:
Jon,

Having the same card, the best I have done is:
Apply the kernel patch to create an event input device for the ir
sensor.
        I'm still seeing some of the issues talked about with the patch:
delayed button presses the most         notable one.
I created a udev rule to map /dev/input/event? -> /dev/input/irremote
        KERNEL=="event*",ATTRS{modalias}=="input:b0018v0000p0000e0000-
e0,1,14,k71,72,73,74,80,9F,A3,A4,A5,A7,A8,D2,D9,16D,174,188,189,192,193,
ramlsfw",SYMLINK="input/
        irremote"
I setup lirc in /etc/lirc/hardware.conf to read from the dev/input
driver on /dev/input/irremote
        # /etc/lirc/hardware.conf
        #
        # Arguments which will be used when launching lircd
        LIRCD_ARGS=""
        #Don't start lircmd even if there seems to be a good config file
        #START_LIRCMD=false
        #Try to load appropriate kernel modules
        LOAD_MODULES=false
        # Run "lircd --driver=help" for a list of supported drivers.
        DRIVER="dev/input"
        # If DEVICE is set to /dev/lirc and devfs is in use /dev/lirc/0
will be
        # automatically used instead
        DEVICE="/dev/input/irremote"
        MODULES=""
        # Default configuration files for your hardware if any
        LIRCD_CONF="/etc/lirc/lircd.conf"
        LIRCMD_CONF=""
And used the lircd.conf file from
http://lirc.sourceforge.net/remotes/kworld/ATSC_110
-------------------------------------------
Nathan Faust


-----Original Message-----
From: linux-dvb-bounces@xxxxxxxxxxx
[mailto:linux-dvb-bounces@xxxxxxxxxxx] On Behalf Of Jonathan Isom
Sent: Sunday, April 01, 2007 9:24 PM
To: linux-dvb@xxxxxxxxxxx
Subject:  kworld atsc 110 remote

Hello
    I'm hoping some one can help me.  I'm trying to make lirc handle
the remote control for the 110 but all the data i get from the card is
from the remote that came with the card.  The codes i receive from the
remote are 1 byte long and match the buttons mapping in the patch
floating around.  I was wondering if maybe you have to init the ir
controller to use it with another remote.
            any ideas
                  Jonathan

_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb




_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

[Index of Archives]     [Linux Media]     [Video 4 Linux]     [Asterisk]     [Samba]     [Xorg]     [Xfree86]     [Linux USB]

  Powered by Linux