Re: [Fwd: Re: New Hauppauge Board] requires multiproto

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



I was directed to http://linuxtv.org/hg/~stoth/multiproto via an
off-list message but this tree is 6 months out of date and does not
compile for me under 2.6.19

Why was this branch not rolled back into the main trunk ?

Will

Will Tatam wrote:
> I sent the following email to the email address recommended for adding
> support for new boards using the connexant chipset, but have had no
> reply, so I'm sending to the list
> 
> Will
> 
> -------- Original Message --------
> Subject: Re: New Hauppauge Board
> Date: Sat, 24 Feb 2007 14:44:56 -0000 (UTC)
> From: will@xxxxxxxxxxxxxx
> To: gunther.mayer@xxxxxxx
> References: <36394.10.0.10.2.1172324031.squirrel@xxxxxxxxxxxxxxxxxxx>
> 
> p.s I've just tried building the latest copy of hg and setting the card=18
> (the value i think it detected the similar DVB-T card as) but still no
> joy, see the enclosed dmesg attachment
> 
> Will
> 
>> I think most of the info you need is on the website
>>
>> http://www.hauppauge.co.uk/pages/products/data_hvr4000.html
>>
>> The card was is very similar to the Nova-T PCI (connexant) that i had
>> previously in thie machine, but this card isn't found by modprobe cx88-dvb
>> The main chip had the same starting number for the chip (CX23882-19), but
>> the last bit CX23882-?? was different. It's a bit of a pain to get the
>> card back out so sorry for not giving the full details
>>
>> The following output was under 2.6.19-1.2288.fc5 but I can't see any
>> mention of the details of this card user the hg version of CARDLIST.cx88
>>
>> # lspci
>> 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>> 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>> 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>> 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>> 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>> 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
>> 00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
>> Controller (rev 80)
>> 00:0f.0 IDE interface: VIA Technologies, Inc.
>> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
>> 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>> Controller (rev 81)
>> 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>> Controller (rev 81)
>> 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>> Controller (rev 81)
>> 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>> Controller (rev 81)
>> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
>> [KT600/K8T800/K8T890 South]
>> 00:11.5 Multimedia audio controller: VIA Technologies, Inc.
>> VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
>> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev
>> 78)
>> 00:14.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and
>> Audio Decoder (rev 05)
>> 00:14.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
>> Decoder [Audio Port] (rev 05)
>> 00:14.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
>> Decoder [MPEG Port] (rev 05)
>> 00:14.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
>> Decoder [IR Port] (rev 05)
>> 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome Pro
>> VGA Adapter (rev 02)
>>
>> lspci -vn
>> 00:00.0 0600: 1106:0259
>>         Subsystem: 1106:aa01
>>         Flags: bus master, 66MHz, medium devsel, latency 8
>>         Memory at d8000000 (32-bit, prefetchable) [size=128M]
>>         Capabilities: [80] AGP version 3.5
>>         Capabilities: [50] Power Management version 2
>>
>> 00:00.1 0600: 1106:1259
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:00.2 0600: 1106:2259
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:00.3 0600: 1106:3259
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:00.4 0600: 1106:4259
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:00.7 0600: 1106:7259
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:01.0 0604: 1106:b198
>>         Flags: bus master, 66MHz, medium devsel, latency 0
>>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>>         Memory behind bridge: e4000000-e5ffffff
>>         Prefetchable memory behind bridge: e0000000-e3ffffff
>>         Capabilities: [70] Power Management version 2
>>
>> 00:0d.0 0c00: 1106:3044 (rev 80) (prog-if 10)
>>         Subsystem: 1106:3044
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at ea002000 (32-bit, non-prefetchable) [size=2K]
>>         I/O ports at c000 [size=128]
>>         Capabilities: [50] Power Management version 2
>>
>> 00:0f.0 0101: 1106:0571 (rev 06) (prog-if 8a)
>>         Subsystem: 1106:aa01
>>         Flags: bus master, medium devsel, latency 32
>>         I/O ports at c400 [size=16]
>>         Capabilities: [c0] Power Management version 2
>>
>> 00:10.0 0c03: 1106:3038 (rev 81)
>>         Subsystem: 1106:aa01
>>         Flags: bus master, medium devsel, latency 32, IRQ 11
>>         I/O ports at c800 [size=32]
>>         Capabilities: [80] Power Management version 2
>>
>> 00:10.1 0c03: 1106:3038 (rev 81)
>>         Subsystem: 1106:aa01
>>         Flags: bus master, medium devsel, latency 32, IRQ 11
>>         I/O ports at cc00 [size=32]
>>         Capabilities: [80] Power Management version 2
>>
>> 00:10.2 0c03: 1106:3038 (rev 81)
>>         Subsystem: 1106:aa01
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         I/O ports at d000 [size=32]
>>         Capabilities: [80] Power Management version 2
>>
>> 00:10.3 0c03: 1106:3038 (rev 81)
>>         Subsystem: 1106:aa01
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         I/O ports at d400 [size=32]
>>         Capabilities: [80] Power Management version 2
>>
>> 00:11.0 0601: 1106:3227
>>         Subsystem: 1106:aa01
>>         Flags: bus master, stepping, medium devsel, latency 0
>>         Capabilities: [c0] Power Management version 2
>>
>> 00:11.5 0401: 1106:3059 (rev 60)
>>         Subsystem: 1106:aa01
>>         Flags: medium devsel, IRQ 7
>>         I/O ports at d800 [size=256]
>>         Capabilities: [c0] Power Management version 2
>>
>> 00:12.0 0200: 1106:3065 (rev 78)
>>         Subsystem: 1106:0102
>>         Flags: bus master, medium devsel, latency 32, IRQ 11
>>         I/O ports at e000 [size=256]
>>         Memory at ea001000 (32-bit, non-prefetchable) [size=256]
>>         Capabilities: [40] Power Management version 2
>>
>> 00:14.0 0400: 14f1:8800 (rev 05)
>>         Subsystem: 0070:6902
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at e6000000 (32-bit, non-prefetchable) [size=16M]
>>         Capabilities: [44] Vital Product Data
>>         Capabilities: [4c] Power Management version 2
>>
>> 00:14.1 0480: 14f1:8811 (rev 05)
>>         Subsystem: 0070:6902
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at e7000000 (32-bit, non-prefetchable) [size=16M]
>>         Capabilities: [4c] Power Management version 2
>>
>> 00:14.2 0480: 14f1:8802 (rev 05)
>>         Subsystem: 0070:6902
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at e8000000 (32-bit, non-prefetchable) [size=16M]
>>         Capabilities: [4c] Power Management version 2
>>
>> 00:14.4 0480: 14f1:8804 (rev 05)
>>         Subsystem: 0070:6902
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at e9000000 (32-bit, non-prefetchable) [size=16M]
>>         Capabilities: [4c] Power Management version 2
>>
>> 01:00.0 0300: 1106:3118 (rev 02)
>>         Subsystem: 1106:3118
>>         Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
>>         Memory at e0000000 (32-bit, prefetchable) [size=64M]
>>         Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
>>         [virtual] Expansion ROM at e5000000 [disabled] [size=64K]
>>         Capabilities: [60] Power Management version 2
>>         Capabilities: [70] AGP version 3.0
>>
>> # lspci -v
>> 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>>         Flags: bus master, 66MHz, medium devsel, latency 8
>>         Memory at d8000000 (32-bit, prefetchable) [size=128M]
>>         Capabilities: [80] AGP version 3.5
>>         Capabilities: [50] Power Management version 2
>>
>> 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>>         Flags: bus master, medium devsel, latency 0
>>
>> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00
>> [Normal decode])
>>         Flags: bus master, 66MHz, medium devsel, latency 0
>>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>>         Memory behind bridge: e4000000-e5ffffff
>>         Prefetchable memory behind bridge: e0000000-e3ffffff
>>         Capabilities: [70] Power Management version 2
>>
>> 00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
>> Controller (rev 80) (prog-if 10 [OHCI])
>>         Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at ea002000 (32-bit, non-prefetchable) [size=2K]
>>         I/O ports at c000 [size=128]
>>         Capabilities: [50] Power Management version 2
>>
>> 00:0f.0 IDE interface: VIA Technologies, Inc.
>> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if
>> 8a [Master SecP PriP])
>>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>>         Flags: bus master, medium devsel, latency 32
>>         I/O ports at c400 [size=16]
>>         Capabilities: [c0] Power Management version 2
>>
>> 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>> Controller (rev 81) (prog-if 00 [UHCI])
>>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>>         Flags: bus master, medium devsel, latency 32, IRQ 11
>>         I/O ports at c800 [size=32]
>>         Capabilities: [80] Power Management version 2
>>
>> 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>> Controller (rev 81) (prog-if 00 [UHCI])
>>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>>         Flags: bus master, medium devsel, latency 32, IRQ 11
>>         I/O ports at cc00 [size=32]
>>         Capabilities: [80] Power Management version 2
>>
>> 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>> Controller (rev 81) (prog-if 00 [UHCI])
>>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         I/O ports at d000 [size=32]
>>         Capabilities: [80] Power Management version 2
>>
>> 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>> Controller (rev 81) (prog-if 00 [UHCI])
>>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         I/O ports at d400 [size=32]
>>         Capabilities: [80] Power Management version 2
>>
>> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
>> [KT600/K8T800/K8T890 South]
>>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>>         Flags: bus master, stepping, medium devsel, latency 0
>>         Capabilities: [c0] Power Management version 2
>>
>> 00:11.5 Multimedia audio controller: VIA Technologies, Inc.
>> VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
>>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>>         Flags: medium devsel, IRQ 7
>>         I/O ports at d800 [size=256]
>>         Capabilities: [c0] Power Management version 2
>>
>> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev
>> 78)
>>         Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded
>> Ethernet Controller on VT8235
>>         Flags: bus master, medium devsel, latency 32, IRQ 11
>>         I/O ports at e000 [size=256]
>>         Memory at ea001000 (32-bit, non-prefetchable) [size=256]
>>         Capabilities: [40] Power Management version 2
>>
>> 00:14.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and
>> Audio Decoder (rev 05)
>>         Subsystem: Hauppauge computer works Inc. Unknown device 6902
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at e6000000 (32-bit, non-prefetchable) [size=16M]
>>         Capabilities: [44] Vital Product Data
>>         Capabilities: [4c] Power Management version 2
>>
>> 00:14.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
>> Decoder [Audio Port] (rev 05)
>>         Subsystem: Hauppauge computer works Inc. Unknown device 6902
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at e7000000 (32-bit, non-prefetchable) [size=16M]
>>         Capabilities: [4c] Power Management version 2
>>
>> 00:14.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
>> Decoder [MPEG Port] (rev 05)
>>         Subsystem: Hauppauge computer works Inc. Unknown device 6902
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at e8000000 (32-bit, non-prefetchable) [size=16M]
>>         Capabilities: [4c] Power Management version 2
>>
>> 00:14.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
>> Decoder [IR Port] (rev 05)
>>         Subsystem: Hauppauge computer works Inc. Unknown device 6902
>>         Flags: bus master, medium devsel, latency 32, IRQ 10
>>         Memory at e9000000 (32-bit, non-prefetchable) [size=16M]
>>         Capabilities: [4c] Power Management version 2
>>
>> 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome Pro
>> VGA Adapter (rev 02) (prog-if 00 [VGA])
>>         Subsystem: VIA Technologies, Inc. S3 Unichrome Pro VGA Adapter
>>         Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
>>         Memory at e0000000 (32-bit, prefetchable) [size=64M]
>>         Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
>>         [virtual] Expansion ROM at e5000000 [disabled] [size=64K]
>>         Capabilities: [60] Power Management version 2
>>         Capabilities: [70] AGP version 3.0
>>
>>
>>
>>
>>
> 
> 
> ------------------------------------------------------------------------
> 
> Linux version 2.6.19-1.2288.fc5 (brewbuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-51)) #1 Sat Feb 10 14:27:07 EST 2007
> BIOS-provided physical RAM map:
>  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
>  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
>  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
>  BIOS-e820: 0000000000100000 - 000000001bff0000 (usable)
>  BIOS-e820: 000000001bff0000 - 000000001bff3000 (ACPI NVS)
>  BIOS-e820: 000000001bff3000 - 000000001c000000 (ACPI data)
>  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> 0MB HIGHMEM available.
> 447MB LOWMEM available.
> Using x86 segment limits to approximate NX protection
> Entering add_active_range(0, 0, 114672) 0 entries of 256 used
> Zone PFN ranges:
>   DMA             0 ->     4096
>   Normal       4096 ->   114672
>   HighMem    114672 ->   114672
> early_node_map[1] active PFN ranges
>     0:        0 ->   114672
> On node 0 totalpages: 114672
>   DMA zone: 32 pages used for memmap
>   DMA zone: 0 pages reserved
>   DMA zone: 4064 pages, LIFO batch:0
>   Normal zone: 863 pages used for memmap
>   Normal zone: 109713 pages, LIFO batch:31
>   HighMem zone: 0 pages used for memmap
> DMI not present or invalid.
> Using APIC driver default
> ACPI: RSDP (v000 CN400                                 ) @ 0x000f6aa0
> ACPI: RSDT (v001 CN400  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bff3000
> ACPI: FADT (v001 CN400  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bff3040
> ACPI: DSDT (v001 CN400  AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
> ACPI: Disabling ACPI support
> Allocating PCI resources starting at 20000000 (gap: 1c000000:e3ff0000)
> Detected 1333.397 MHz processor.
> Built 1 zonelists.  Total pages: 113777
> Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
> No local APIC present or hardware disabled
> mapped APIC to ffffd000 (0139c000)
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> CPU 0 irqstacks, hard=c076c000 soft=c076b000
> PID hash table entries: 2048 (order: 11, 8192 bytes)
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Memory: 448460k/458688k available (2083k kernel code, 9600k reserved, 807k data, 228k init, 0k highmem)
> virtual kernel memory layout:
>     fixmap  : 0xfff9a000 - 0xfffff000   ( 404 kB)
>     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
>     vmalloc : 0xdc800000 - 0xff7fe000   ( 559 MB)
>     lowmem  : 0xc0000000 - 0xdbff0000   ( 447 MB)
>       .init : 0xc072d000 - 0xc0766000   ( 228 kB)
>       .data : 0xc0608c72 - 0xc06d2af4   ( 807 kB)
>       .text : 0xc0400000 - 0xc0608c72   (2083 kB)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> Calibrating delay using timer specific routine.. 2668.74 BogoMIPS (lpj=1334373)
> Security Framework v1.0.0 initialized
> SELinux:  Initializing.
> SELinux:  Starting in permissive mode
> selinux_register_security:  Registering secondary module capability
> Capability LSM initialized as secondary
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000 00000000 00000000 00000000
> CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
> CPU: L2 Cache: 64K (32 bytes/line)
> CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000 00000000 000000dd 00000000
> CPU: Centaur VIA Nehemiah stepping 08
> Checking 'hlt' instruction... OK.
> checking if image is initramfs... it is
> Freeing initrd memory: 1542k freed
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfad70, last bus=1
> PCI: Using configuration type 1
> Setting up standard PCI resources
> ACPI: Interpreter disabled.
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI: disabled
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> PCI: Probing PCI hardware
> PCI: Probing PCI hardware (bus 00)
> Boot video device is 0000:01:00.0
> PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
> NetLabel: Initializing
> NetLabel:  domain hash size = 128
> NetLabel:  protocols = UNLABELED CIPSOv4
> NetLabel:  unlabeled traffic allowed by default
> PCI: Bridge: 0000:00:01.0
>   IO window: disabled.
>   MEM window: e4000000-e5ffffff
>   PREFETCH window: e0000000-e3ffffff
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
> TCP established hash table entries: 16384 (order: 6, 262144 bytes)
> TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
> TCP: Hash tables configured (established 16384 bind 8192)
> TCP reno registered
> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
> audit: initializing netlink socket (disabled)
> audit(1172327905.858:1): initialized
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> SELinux:  Registering netfilter hooks
> ksign: Installing public key data
> Loading keyring
> - Added public key 38BFE5B32FEF5C5
> - User ID: Red Hat, Inc. (Kernel Module GPG key)
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> PCI: Bypassing VIA 8237 APIC De-Assert Message
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Real Time Clock Driver v1.12ac
> Non-volatile memory driver v1.2
> Linux agpgart interface v0.101 (c) Dave Jones
> agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset
> agpgart: AGP aperture is 128M @ 0xd8000000
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller at PCI slot 0000:00:0f.0
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
>     ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:DMA, hdb:pio
>     ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:DMA, hdd:pio
> Probing IDE interface ide0...
> hda: SAMSUNG SP1604N, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hdc: SONY DVD RW DRU-510A, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: max request size: 512KiB
> hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
> hda: cache flushes supported
>  hda: hda1 hda2
> ide-floppy driver 0.99.newide
> usbcore: registered new interface driver libusual
> usbcore: registered new interface driver hiddev
> usbcore: registered new interface driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> PNP: No PS/2 controller found. Probing ports directly.
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> mice: PS/2 mouse device common for all mice
> TCP bic registered
> Initializing XFRM netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Using IPI Shortcut mode
> Time: tsc clocksource has been installed.
> Freeing unused kernel memory: 228k freed
> Write protecting the kernel read-only data: 391k
> input: AT Translated Set 2 keyboard as /class/input/input0
> logips2pp: Detected unknown logitech mouse model 1
> input: PS/2 Logitech Mouse as /class/input/input1
> device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@xxxxxxxxxx
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> SELinux:  Disabled at runtime.
> SELinux:  Unregistering netfilter hooks
> audit(1172327910.452:2): selinux=0 auid=4294967295
> hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> Linux video capture interface: v2.00
> input: PC Speaker as /class/input/input2
> via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
> PCI: setting IRQ 11 as level-triggered
> PCI: Found IRQ 11 for device 0000:00:12.0
> PCI: Sharing IRQ 11 with 0000:00:10.0
> PCI: Sharing IRQ 11 with 0000:00:10.1
> eth0: VIA Rhine II at 0xea001000, 00:40:63:e5:09:2d, IRQ 11.
> eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
> cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
> CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge Nova-T DVB-T [card=18,insmod option]
> TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
> cx2388x v4l2 driver version 0.0.6 loaded
> tveeprom 1-0050: Hauppauge model 69009, rev B2A0, serial# 1243050
> tveeprom 1-0050: MAC address is 00-0D-FE-12-F7-AA
> tveeprom 1-0050: tuner model is Philips FMD1216ME (idx 100, type 63)
> tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
> tveeprom 1-0050: audio processor is CX882 (idx 33)
> tveeprom 1-0050: decoder processor is CX882 (idx 25)
> tveeprom 1-0050: has radio, has IR receiver, has no IR transmitter
> cx88[0]: warning: unknown hauppauge model #69009
> cx88[0]: hauppauge eeprom: model=69009
> input: cx88 IR (Hauppauge Nova-T DVB-T as /class/input/input3
> cx88[0]/2: cx2388x 8802 Driver Manager
> PCI: setting IRQ 10 as level-triggered
> PCI: Found IRQ 10 for device 0000:00:14.2
> PCI: Sharing IRQ 10 with 0000:00:0d.0
> PCI: Sharing IRQ 10 with 0000:00:10.2
> PCI: Sharing IRQ 10 with 0000:00:10.3
> PCI: Sharing IRQ 10 with 0000:00:14.0
> PCI: Sharing IRQ 10 with 0000:00:14.1
> PCI: Sharing IRQ 10 with 0000:00:14.4
> cx88[0]/2: found at 0000:00:14.2, rev: 5, irq: 10, latency: 32, mmio: 0xe8000000
> PCI: Found IRQ 10 for device 0000:00:14.0
> PCI: Sharing IRQ 10 with 0000:00:0d.0
> PCI: Sharing IRQ 10 with 0000:00:10.2
> PCI: Sharing IRQ 10 with 0000:00:10.3
> PCI: Sharing IRQ 10 with 0000:00:14.1
> PCI: Sharing IRQ 10 with 0000:00:14.2
> PCI: Sharing IRQ 10 with 0000:00:14.4
> cx88[0]/0: found at 0000:00:14.0, rev: 5, irq: 10, latency: 32, mmio: 0xe6000000
> cx88[0]/0: registered device video0 [v4l2]
> cx88[0]/0: registered device vbi0
> cx88[0]/0: registered device radio0
> PCI: setting IRQ 7 as level-triggered
> PCI: Found IRQ 7 for device 0000:00:11.5
> PCI: Setting latency timer of device 0000:00:11.5 to 64
> cx2388x alsa driver version 0.0.6 loaded
> PCI: Found IRQ 10 for device 0000:00:14.1
> PCI: Sharing IRQ 10 with 0000:00:0d.0
> PCI: Sharing IRQ 10 with 0000:00:10.2
> PCI: Sharing IRQ 10 with 0000:00:10.3
> PCI: Sharing IRQ 10 with 0000:00:14.0
> PCI: Sharing IRQ 10 with 0000:00:14.2
> PCI: Sharing IRQ 10 with 0000:00:14.4
> cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
> USB Universal Host Controller Interface driver v3.0
> PCI: Found IRQ 11 for device 0000:00:10.0
> PCI: Sharing IRQ 11 with 0000:00:10.1
> PCI: Sharing IRQ 11 with 0000:00:12.0
> uhci_hcd 0000:00:10.0: UHCI Host Controller
> uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
> uhci_hcd 0000:00:10.0: irq 11, io base 0x0000c800
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> PCI: Found IRQ 11 for device 0000:00:10.1
> PCI: Sharing IRQ 11 with 0000:00:10.0
> PCI: Sharing IRQ 11 with 0000:00:12.0
> uhci_hcd 0000:00:10.1: UHCI Host Controller
> uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:10.1: irq 11, io base 0x0000cc00
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> PCI: Found IRQ 10 for device 0000:00:10.2
> PCI: Sharing IRQ 10 with 0000:00:0d.0
> PCI: Sharing IRQ 10 with 0000:00:10.3
> PCI: Sharing IRQ 10 with 0000:00:14.0
> PCI: Sharing IRQ 10 with 0000:00:14.1
> PCI: Sharing IRQ 10 with 0000:00:14.2
> PCI: Sharing IRQ 10 with 0000:00:14.4
> uhci_hcd 0000:00:10.2: UHCI Host Controller
> uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:10.2: irq 10, io base 0x0000d000
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> PCI: Found IRQ 10 for device 0000:00:10.3
> PCI: Sharing IRQ 10 with 0000:00:0d.0
> PCI: Sharing IRQ 10 with 0000:00:10.2
> PCI: Sharing IRQ 10 with 0000:00:14.0
> PCI: Sharing IRQ 10 with 0000:00:14.1
> usb 1-1: new full speed USB device using uhci_hcd and address 2
> PCI: Sharing IRQ 10 with 0000:00:14.2
> PCI: Sharing IRQ 10 with 0000:00:14.4
> uhci_hcd 0000:00:10.3: UHCI Host Controller
> uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:10.3: irq 10, io base 0x0000d400
> usb usb4: configuration #1 chosen from 1 choice
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> ieee1394: Initialized config rom entry `ip1394'
> usb 1-1: configuration #1 chosen from 1 choice
> PCI: Found IRQ 10 for device 0000:00:0d.0
> PCI: Sharing IRQ 10 with 0000:00:10.2
> PCI: Sharing IRQ 10 with 0000:00:10.3
> PCI: Sharing IRQ 10 with 0000:00:14.0
> PCI: Sharing IRQ 10 with 0000:00:14.1
> PCI: Sharing IRQ 10 with 0000:00:14.2
> PCI: Sharing IRQ 10 with 0000:00:14.4
> ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10]  MMIO=[ea002000-ea0027ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
> usb 1-2: new low speed USB device using uhci_hcd and address 3
> usb 1-2: configuration #1 chosen from 1 choice
> input: CHESEN USB Keyboard as /class/input/input4
> input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:10.0-2
> input: CHESEN USB Keyboard as /class/input/input5
> input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:10.0-2
> ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0040635000071590]
> drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04E8 pid 0x3242
> usbcore: registered new interface driver usblp
> drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
> Floppy drive(s): fd0 is unknown type 15 (usb?), fd1 is unknown type 15 (usb?)
> floppy0: no floppy controllers found
> lp: driver loaded but no devices found
> NET: Registered protocol family 10
> lo: Disabled Privacy Extensions
> Mobile IPv6
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> EXT3 FS on dm-0, internal journal
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on hda1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on dm-1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> Adding 917496k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1 across:917496k
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> audit(1172327938.750:3): audit_pid=1692 old=0 by auid=4294967295
> Bluetooth: Core ver 2.11
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> Bluetooth: L2CAP ver 2.8
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: RFCOMM socket layer initialized
> Bluetooth: RFCOMM TTY layer initialized
> Bluetooth: RFCOMM ver 1.8
> Bluetooth: HIDP (Human Interface Emulation) ver 1.1
> eth0: no IPv6 routers present
> Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
> NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
> NFSD: starting 90-second grace period
> cx2388x dvb driver version 0.0.6 loaded
> cx8802_register_driver() ->registering driver type=dvb access=shared
> CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge Nova-T DVB-T [card=18]
> cx88[0]/2: cx2388x based dvb card
> cx22702_readreg: readreg error (ret == -121)
> cx88[0]: frontend initialization failed
> cx8802_dvb_probe dvb_register failed err = -1
> cx8802_register_driver() ->probe failed err = -1
> saa7146: register extension 'budget_ci dvb'.
> [drm] Initialized drm 1.0.1 20051102
> [drm] Initialized via 2.10.0 20060529 on minor 0
> agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
> agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
> agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
> 
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb



_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

[Index of Archives]     [Linux Media]     [Video 4 Linux]     [Asterisk]     [Samba]     [Xorg]     [Xfree86]     [Linux USB]

  Powered by Linux