Cabrito Estrabico wrote:
Hartmut Hackmann a écrit :
Hi,
Cabrito Estrabico wrote:
Hello,
I'm Ubuntu 6.06 LTS user on kernell 2.6.15-27-k7 with the last
v4l-dvb sources compiled to make
this Pinnacle 310i runing dvb-t with dvb-fe-tda10046.fw firmware.
Being from France I use the secam videostandard and everything is ok
for analogue tv.
Here is the dmesg output when probing saa7134 module with secam=l
option :
[17179647.088000] saa7130/34: v4l2 driver version 0.2.14 loaded
[17179647.088000] **** SET: Misaligned resource pointer: f6594902
Type 07 Len 0
[17179647.092000] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[17179647.092000] ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2]
-> GSI 17 (level, low) -> IRQ 66
[17179647.092000] saa7133[0]: found at 0000:05:07.0, rev: 208, irq:
66, latency: 32, mmio: 0xd3000000
[17179647.092000] saa7133[0]: subsystem: 11bd:002f, board: Pinnacle
PCTV 310i [card=101,autodetected]
[17179647.092000] saa7133[0]: board init: gpio is 600c000
[17179647.240000] saa7133[0]: i2c eeprom 00: bd 11 2f 00 54 20 1c 00
43 43 a9 1c 55 d2 b2 92
[17179647.240000] saa7133[0]: i2c eeprom 10: ff e0 60 06 ff 20 ff ff
00 30 8d 2c 1a 07 ff ff
[17179647.240000] saa7133[0]: i2c eeprom 20: 01 2c 01 02 02 01 04 31
98 ff 00 a6 ff 21 00 c2
[17179647.240000] saa7133[0]: i2c eeprom 30: 96 10 03 32 15 20 ff ff
0c 22 17 77 03 1c 88 97
[17179647.240000] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff
[17179647.240000] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff
[17179647.240000] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff
[17179647.240000] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff
[17179647.344000] tuner 5-004b: chip found @ 0x96 (saa7133[0])
[17179647.396000] tuner 5-004b: setting tuner address to 61
[17179647.436000] tuner 5-004b: type set to tda8290+75a
[17179647.508000] saa7133[0]: registered device video0 [v4l2]
[17179647.508000] saa7133[0]: registered device vbi0
[17179647.508000] saa7133[0]: registered device radio0
[17179647.548000] saa7134 ALSA driver for DMA sound loaded
[17179647.548000] saa7133[0]/alsa: saa7133[0] at 0xd3000000 irq 66
registered as card -1
next, modprobe saa1734-dvb :
[17179811.560000] DVB: registering new adapter (saa7133[0]).
[17179811.560000] DVB: registering frontend 0 (Philips TDA10046H
DVB-T)...
then, scanning tuning data file :
[17179869.076000] tda1004x: setting up plls for 48MHz sampling clock
[17179869.344000] tda1004x: found firmware revision 20 -- ok
But scan result is : ERROR: initial tuning
failed
dumping lists (0 services)
Done.
and femon give :
using '/dev/dvb/adapter0/frontend0'
FE: Philips TDA10046H DVB-T (TERRESTRIAL)
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
.............. .................... .............
..................... ........................
.............. .................... .............
..................... ........................
etc etc
I want to add that I've already manage to have dvb-t on my Ubuntu
with an other card.
So, from where come this trouble ; hardware, configuration ?
Thank you for any help you could give.
Cabrito
I think the "initial tuning failed" is not a problem. In this
configuration,
the channel decoder needs some time to settle. This can give you a
timeout
in the first attempt, the second should be better.
I guess your problem is that your initial config file is not ok:
Some drivers ignore the parameters for FEC, guard interval etc. For the
TDA10046, you need to set them to AUTO to let the chip determine these
automatically. Unfortunately, there are some bad config files floating
around.
The other issue is that in some countries, the transmitters are off the
channel frequency by +/-167kHz. This is the case in Britain, France and
Australia, probalbly others too. In the current implementation, you need
to correct this manually.
Hartmut
Hi Hartmut,
the « other issue » is the right one :
I just had to shift forward by 167 kHz each channel frequency in the
tuning data file to make the TDA10046 driver locking channels.
Thanks for the info! We are talking about France?
I wanted to notice that thanks to saa7134 ALSA driver, sound is ok for
dvb-t but cable connected from card to pc is needed for analogue tv.
It's not a problem indeed.
This is not fully correct. With DVB-T, sound is decoded and handled in
Software and directly transferred to the soundcard. The saa7134-alsa
module is not involved. You can use it to digitally transfer the audio
data from analog TV to the sound card (without the cable). The big problem
is that currently only few applications support this, the conversion and
transfer need to be handled in user space.
A Minor issue is that the current version of the module does not initialize
its mixer device, this also needs to be done with an external app. I am
going to change this too.
Thank you Harmtmut for sharing your big experience.
Cabrito
You're welcome
Hartmut
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
