Cabrito Estrabico ha scritto:
Hello,
I'm Ubuntu 6.06 LTS user on kernell 2.6.15-27-k7 with the last v4l-dvb
sources compiled to make
this Pinnacle 310i runing dvb-t with dvb-fe-tda10046.fw firmware.
Being from France I use the secam videostandard and everything is ok
for analogue tv.
Here is the dmesg output when probing saa7134 module with secam=l
option :
[17179647.088000] saa7130/34: v4l2 driver version 0.2.14 loaded
[17179647.088000] **** SET: Misaligned resource pointer: f6594902 Type
07 Len 0
[17179647.092000] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[17179647.092000] ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2]
-> GSI 17 (level, low) -> IRQ 66
[17179647.092000] saa7133[0]: found at 0000:05:07.0, rev: 208, irq:
66, latency: 32, mmio: 0xd3000000
[17179647.092000] saa7133[0]: subsystem: 11bd:002f, board: Pinnacle
PCTV 310i [card=101,autodetected]
[17179647.092000] saa7133[0]: board init: gpio is 600c000
[17179647.240000] saa7133[0]: i2c eeprom 00: bd 11 2f 00 54 20 1c 00
43 43 a9 1c 55 d2 b2 92
[17179647.240000] saa7133[0]: i2c eeprom 10: ff e0 60 06 ff 20 ff ff
00 30 8d 2c 1a 07 ff ff
[17179647.240000] saa7133[0]: i2c eeprom 20: 01 2c 01 02 02 01 04 31
98 ff 00 a6 ff 21 00 c2
[17179647.240000] saa7133[0]: i2c eeprom 30: 96 10 03 32 15 20 ff ff
0c 22 17 77 03 1c 88 97
[17179647.240000] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff
[17179647.240000] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff
[17179647.240000] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff
[17179647.240000] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff
[17179647.344000] tuner 5-004b: chip found @ 0x96 (saa7133[0])
[17179647.396000] tuner 5-004b: setting tuner address to 61
[17179647.436000] tuner 5-004b: type set to tda8290+75a
[17179647.508000] saa7133[0]: registered device video0 [v4l2]
[17179647.508000] saa7133[0]: registered device vbi0
[17179647.508000] saa7133[0]: registered device radio0
[17179647.548000] saa7134 ALSA driver for DMA sound loaded
[17179647.548000] saa7133[0]/alsa: saa7133[0] at 0xd3000000 irq 66
registered as card -1
next, modprobe saa1734-dvb :
[17179811.560000] DVB: registering new adapter (saa7133[0]).
[17179811.560000] DVB: registering frontend 0 (Philips TDA10046H
DVB-T)...
then, scanning tuning data file :
[17179869.076000] tda1004x: setting up plls for 48MHz sampling clock
[17179869.344000] tda1004x: found firmware revision 20 -- ok
But scan result is :
ERROR: initial tuning failed
dumping lists (0 services)
Done.
and femon give :
using '/dev/dvb/adapter0/frontend0'
FE: Philips TDA10046H DVB-T (TERRESTRIAL)
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
.............. .................... .............
..................... ........................
.............. .................... .............
..................... ........................
etc etc
I want to add that I've already manage to have dvb-t on my Ubuntu with
an other card.
So, from where come this trouble ; hardware, configuration ?
Thank you for any help you could give.
Cabrito
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
seems that you have done all steps like but here i repeat :
make all & make install from v4l dir
perl *path_to_v4l_dir*/linux/Documentation/dvb/get_dvb_firmware tda10046 //to get firmware
cp *path_to_v4l_dir*/linux/Documentation/dvb/get_dvb_firmware/dvb-fe-tda10046.fw /lib/firmware //copy firmware where hotplug search for it
reboot ;) it's better ;)
I have ubuntu 606 like you. Try to compile a new vanilla kernel from source.
I say this because when i have tried to compile current v4l my messages tell me the to get
work perfectly all features i have to compile at least kernel 2.6.16. So i have download and
compile 2.6.18 kernel. If you have problems look at this to compile a new kernel under ubuntu :
http://www.ubuntuforums.org/showthread.php?t=217657&highlight=howto+grub
I don't know if is this the problem but if you receive during v4l compilation the same message,
try to update kernel.
Maybe other people can tell u more than me ;)
best regards
kev
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
