ThomP Pontoppidan wrote: > Hi, > > I just tried installing my HVR-1300 (again) seeing that it has been merged > with the main tree. I downloaded this tree: v4l-dvb-7efa405e2d66 and did: > > make ivtv > make > make install > > After a reboot, dmesg shows this: > cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded > cx2388x v4l2 driver version 0.0.6 loaded > sis630_smbus 0000:00:02.0: SIS630 comp. bus not detected, module not > inserted. > CORE cx88[0]: subsystem: 0070:9601, board: Hauppauge WinTV-HVR1300 > DVB-T/Hybrid MPEG Encoder [card=56,autodetected] > TV tuner 63 at 0x1fe, Radio tuner -1 at 0x1fe > tveeprom 0-0050: Hauppauge model 96019, rev C6A0, serial# 544048 > tveeprom 0-0050: MAC address is 00-0D-FE-08-4D-30 > tveeprom 0-0050: tuner model is Philips FMD1216ME (idx 100, type 63) > tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) > ATSC/DVB Digital (eeprom 0xf4) > tveeprom 0-0050: audio processor is CX882 (idx 33) > tveeprom 0-0050: decoder processor is CX882 (idx 25) > tveeprom 0-0050: has radio, has IR remote > cx88[0]: hauppauge eeprom: model=96019 > input: cx88 IR (Hauppauge WinTV-HVR130 as /class/input/input2 > cx88[0]/2: cx2388x 8802 Driver Manager > ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 > PCI: setting IRQ 11 as level-triggered > ACPI: PCI Interrupt 0000:00:0b.2[A] -> Link [LNKB] -> GSI 11 (level, > low) -> > IRQ 11 > cx88[0]/2: found at 0000:00:0b.2, rev: 5, irq: 11, latency: 64, mmio: > 0xce000000 > ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 11 (level, > low) -> > IRQ 11 > cx88[0]/0: found at 0000:00:0b.0, rev: 5, irq: 11, latency: 64, mmio: > 0xcc000000 > USB Universal Host Controller Interface driver v3.0 > tuner 0-0043: chip found @ 0x86 (cx88[0]) > tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) > tuner 0-0061: chip found @ 0xc2 (cx88[0]) > tuner 0-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner) > tuner 0-0063: chip found @ 0xc6 (cx88[0]) > wm8775 0-001b: chip found @ 0x36 (cx88[0]) > cx88[0]/0: registered device video0 [v4l2] > cx88[0]/0: registered device vbi0 > cx88[0]/0: registered device radio0 > > The way I read this, it found the analog part but not the DVB-part? I > already got a Nova-T-500 working and after installing the HVR I still have > only two adapters in /dev/dvb/ > > Any clues? try: modprobe cx88-dvb cx88-dvb and cx88-blackbird modules do not auto-load anymore, after recent changes to cx88-mpeg, which allow both cx88-dvb and cx88-blackbird to function on the same hardware. HTH, Mike _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
