I get similar problems on the same card (14aa:0225 - Feb 06 version from memory?). I cannot tune however, on either frontend. Others have this card working fine, though. Possibly something to do with our hardware? [I have no idea at all.] I am using an Athlon XP on a Asus A7V600 motherboard (in the UK). Regards, Benjie. d-PUNk wrote: > Hi! > > I am using a Freecom DVB-T usb device which has the usb id 14aa:0225 > before the driver / firmware is loaded. My system is gentoo linux with > 2.6.17-gentoo-r8 kernel source. I download the latest snapshot of the > linux-dvb drivers via mercurial and installed them. I took the firmware > named dvb-usb-wt220u-fc03.fw. When I modprobe dvb_usb_dtt200u I get: > > dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' > in warm state. > dvb-usb: will use the device's hardware PID filter (table count: 15). > DVB: registering new adapter (WideView WT-220U PenType Receiver > (Typhoon/Freecom)). > DVB: registering frontend 0 (WideView USB DVB-T)... > input: IR-receiver inside an USB DVB receiver as /class/input/input8 > dvb-usb: schedule remote query interval to 300 msecs. > dvb-usb: WideView WT-220U PenType Receiver (Typhoon/Freecom) > successfully initialized and connected. > dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' > in warm state. > dvb-usb: will use the device's hardware PID filter (table count: 15). > DVB: registering new adapter (WideView WT-220U PenType Receiver > (Typhoon/Freecom)). > DVB: registering frontend 1 (WideView USB DVB-T)... > input: IR-receiver inside an USB DVB receiver as /class/input/input9 > dvb-usb: schedule remote query interval to 300 msecs. > dvb-usb: WideView WT-220U PenType Receiver (Typhoon/Freecom) > successfully initialized and connected. > usbcore: registered new driver dvb_usb_dtt200u > dvb-usb: recv bulk message failed: -110 > > Now I am quite confused why I find two directories in /dev/dvb named > adapter0 and adapter1 with > > adapter0: > > crw-rw---- 1 root video 212, 4 2. Okt 16:50 demux0 > crw-rw---- 1 root video 212, 5 2. Okt 16:50 dvr0 > crw-rw---- 1 root video 212, 3 2. Okt 16:50 frontend0 > crw-rw---- 1 root video 212, 7 2. Okt 16:50 net0 > > adapter1 > > crw-rw---- 1 root video 212, 68 2. Okt 16:50 demux0 > crw-rw---- 1 root video 212, 69 2. Okt 16:50 dvr0 > crw-rw---- 1 root video 212, 67 2. Okt 16:50 frontend0 > crw-rw---- 1 root video 212, 71 2. Okt 16:50 net0 > > > I can dvbscan on both adapters with correct behaviour (but not at the > same time) and vlc shows tv when using the generated channels.conf. > > I would like to use vdr for recording but this gives me a lot of errors > (adapter1/demux0: too many open files ... and more). > > Can anyone tell me why I got to devices? dmesg looks to me like the > firmware loads twice. Also two ir-receiver are registered and the > class/input/inputX increases every time I unload and load the > dvb_usb_dtt200u. > > > Thank you very much for reading this. > > Bye > Peter > > > > > > > > _______________________________________________ > linux-dvb mailing list > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > > _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
