since about 30.07.07 the hg drivers seem to be broken for Airstar2 and Pinnacle PCTV 300i I think the reason is in both cases the "Unable to find symbol mt352_attach()" on this machine Siemens DVB-C + TT 1500C are working, but not the Airstar2: saa7146: found saa7146 @ mem d09c6000 (revision 1, irq 11) (0x110a,0x0000). DVB: registering new adapter (Fujitsu Siemens DVB-C). adapter has MAC addr = 00:d0:5c:01:0f:80 dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80f226 23 dvb-ttpci: firmware @ card 0 supports CI link layer interface dvb-ttpci: DVB-C w/o analog module @ card 0 detected saa7146_vv: saa7146 (0): registered device video1 [v4l2] saa7146_vv: saa7146 (0): registered device vbi1 [v4l2] DVB: registering frontend 0 (VLSI VES1820 DVB-C)... input: DVB on-card IR receiver as /class/input/input0 dvb-ttpci: found av7110-0. saa7146: register extension 'budget_ci dvb'. ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12 saa7146: found saa7146 @ mem d0a50000 (revision 1, irq 12) (0x13c2,0x1010). saa7146 (1): dma buffer size 192512 DVB: registering new adapter (TT-Budget-C-CI PCI). adapter has MAC addr = 00:d0:5c:04:7b:0c input: Budget-CI dvb ir receiver saa7146 (1) as /class/input/input1 budget_ci: CI interface initialised DVB: registering frontend 1 (ST STV0297 DVB-C)... dvb_ca adapter 1: DVB CAM detected and initialised successfully saa7146: register extension 'budget dvb'. saa7146: register extension 'budget_av'. b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfu lly flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 ACPI: PCI Interrupt 0000:01:01.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 DVB: registering new adapter (FlexCop Digital TV device). b2c2-flexcop: MAC address = 00:d0:d7:0a:9a:08 DVB: Unable to find symbol stv0299_attach() DVB: Unable to find symbol mt352_attach() DVB: Unable to find symbol nxt200x_attach() DVB: Unable to find symbol lgdt330x_attach() DVB: Unable to find symbol bcm3510_attach() b2c2-flexcop: i2c master_xfer failed stv0297_readreg: readreg error (reg == 0x80, ret == -121) DVB: Unable to find symbol vp310_mt312_attach() b2c2-flexcop: no frontend driver found for this B2C2/FlexCop adapter on the second machine the Pinnacle does not work: saa7134[0]: found at 0000:00:09.0, rev: 1, irq: 12, latency: 32, mmio: 0xde10000 0 saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50 ,autodetected] saa7134[0]: board init: gpio is cc06000 saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92 saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 60: 0c 22 17 44 02 97 cf 48 ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 70: 00 30 8d 15 1f 09 ff ff ff ff ff ff ff ff ff ff tuner 2-0043: chip found @ 0x86 (saa7134[0]) tda9887 2-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 2-0060: Chip ID is not zero. It is not a TEA5767 tuner 2-0060: chip found @ 0xc0 (saa7134[0]) tuner 2-0060: microtune: companycode=3cbf part=42 rev=2f tuner 2-0060: microtune MT2050 found, OK saa7134[0]: registered device video0 [v4l2] saa7134[0]: registered device vbi0 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 saa7134[1]: found at 0000:00:0a.0, rev: 1, irq: 11, latency: 32, mmio: 0xde10100 0 saa7134[1]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50 ,autodetected] saa7134[1]: board init: gpio is c806000 tuner 3-0043: chip found @ 0x86 (saa7134[1]) tda9887 3-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 3-0060: Chip ID is not zero. It is not a TEA5767 tuner 3-0060: chip found @ 0xc0 (saa7134[1]) tuner 3-0060: microtune: companycode=3cbf part=42 rev=22 tuner 3-0060: microtune MT2050 found, OK saa7134[1]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92 saa7134[1]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff saa7134[1]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff saa7134[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[1]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff saa7134[1]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[1]: i2c eeprom 60: 0c 22 17 44 02 97 cf 47 ff ff ff ff ff ff ff ff saa7134[1]: i2c eeprom 70: 00 30 8d 15 1f 08 ff ff ff ff ff ff ff ff ff ff saa7134[1]: registered device video1 [v4l2] saa7134[1]: registered device vbi1 saa7134[0]: pinnacle 300i dvb setup DVB: Unable to find symbol mt352_attach() saa7134[0]: frontend initialization failed hg from 22.07.06 works fine for both cards. -- Der GMX SmartSurfer hilft bis zu 70% Ihrer Onlinekosten zu sparen! Ideal für Modem und ISDN: http://www.gmx.net/de/go/smartsurfer _______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
