I've installed knoppmythtv latest version (2.6.15-cw-2), downloaded
and recompiled v4l-dvb and added the appropriate firmware updates to /
usr/lib/hotplug/firmware.
So now the card is auto detected correctly type 44, most of the time.
Sometimes I get some errors in dmesg about the device being plugged
into a 1.1 port (a7n8x has 1.1 and 2.0 controllers).
There are always cx88[0]/2: cx8802_timeout errors, pretty sure that
is when I attempt to use tzap on the dodgy device.
lsusb -v reports the device as usb2.0
The end result is that doing a tzap with adapter 0 doesn't work
correctly, The first line has a little signal and subsequent lines
have 0 signal.
tzap with adapter 1 get's lock.
Hardware:
A7N8X-E(Deluxe)
FX5200
I have tried moving some things around hardware wise, pulled some
stuff out to reduce power consumption etc.
Device 1 is good
sh-3.00$ tzap -a 1 "ABC TV Brisbane"
using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
reading channels from file '/home/mythtv/.tzap/channels.conf'
tuning to 226500000 Hz
video pid 0x0200, audio pid 0x028a
status 01 | signal 2e5f | snr 0000 | ber 00000000 | unc 00000000 |
status 1f | signal 251f | snr cdcd | ber 00000000 | unc 00000000 |
FE_HAS_LOCK
status 1f | signal 267f | snr d2d2 | ber 00000000 | unc 00000000 |
FE_HAS_LOCK
Device 0 is bad
sh-3.00$ tzap "ABC TV Brisbane"
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
reading channels from file '/home/mythtv/.tzap/channels.conf'
tuning to 226500000 Hz
video pid 0x0200, audio pid 0x028a
status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 |
signal was 000f constantly, but on other runs it starts at 128f.
there is a usb error but later on when ehci is init it indicates that
a device is found ok.
here is the complete dmesg dump, notice the timeout's at the end, do
I need to increase latency on something?
Linux version 2.6.15-chw-2 (root@xxxxxxxxxxxxxxxxxx) (gcc version
3.3.5 (Debian
1:3.3.5-12)) #1 SMP PREEMPT Thu Jan 5 08:10:40 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 126960 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:0
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f6d60
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @
0x1fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @
0x1fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @
0x1fff74c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @
0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=Linux ro root=301 splash=silent
apm=power-o
ff nomce
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1243.420 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 512964k/524224k available (3151k kernel code, 10732k
reserved, 1029k dat
a, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
Calibrating delay using timer specific routine.. 2488.89 BogoMIPS
(lpj=1244448)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000
00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
00000000 0
0000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
00000000 0000000
0 00000000
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) stepping 00
Total of 1 processors activated (2488.89 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
checking if image is initramfs...it isn't (no cpio magic); looks like
an initrd
Freeing initrd memory: 56k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb4b0, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post
a report
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4200-0x427f has been reserved
pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
pnp: 00:01: ioport range 0x5000-0x503f has been reserved
pnp: 00:01: ioport range 0x5500-0x553f has been reserved
PCI: Bridge: 0000:00:08.0
IO window: 9000-afff
MEM window: de000000-e1ffffff
PREFETCH window: 30000000-300fffff
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: dc000000-ddffffff
PREFETCH window: d0000000-d7ffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFS: nTxBlock = 4009, nTxLock = 32072
SGI XFS with ACLs, security attributes, realtime, large block
numbers, no debug
enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
isapnp: ScanniPNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: IC35L040AVER07-0, ATA DISK drive
hdb: ATAPI DVD-ROM 16X Maximum, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CW038D ATAPI CD-R/RW, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
ng for PnP cards...
isapnp: No Plug & Play device found
hda: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=65535/16/63,
UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdb: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
libata version 1.20 loaded.
sata_sil 0000:01:0b.0: version 0.9
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level,
high) -> IR
Q 16
ata1: SATA max UDMA/100 cmd 0xE0802080 ctl 0xE080208A bmdma
0xE0802000 irq 16
ata2: SATA max UDMA/100 cmd 0xE08020C0 ctl 0xE08020CA bmdma
0xE0802008 irq 16
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01
87:4003 88:207f
ata1: dev 0 ATA-6, max UDMA/133, 312581808 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
Vendor: ATA Model: ST3160827AS Rev: 3.03
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 3304.000 MB/sec
raid5: using function: pIII_sse (3304.000 MB/sec)
raid6: int32x1 472 MB/s
raid6: int32x2 593 MB/s
raid6: int32x4 355 MB/s
raid6: int32x8 355 MB/s
raid6: mmxx1 1035 MB/s
raid6: mmxx2 1714 MB/s
raid6: sse1x1 992 MB/s
raid6: sse1x2 1628 MB/s
raid6: using algorithm sse1x2 (1628 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: faulty personality registered as nr 10
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx
NET: Registered protocol family 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 393216 bytes)
TCP bind hash table entries: 32768 (order: 6, 393216 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI No-Shortcut mode
Suspend2 Core.
Suspend2 Compression Driver loading.
Suspend2 Encryption Driver loading.
Suspend2 Swap Writer loading.
Suspend2 FileWriter loading.
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
input: AT Translated Set 2 keyboard as /class/input/input0
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
(fs/jbd/recovery.c, 255): journal_recover: JBD: recovery, exit status
0, recover
ed transactions 20217 to 20311
(fs/jbd/recovery.c, 257): journal_recover: JBD: Replayed 1863 and
revoked 3/14 b
locks
EXT3-fs warning: maximal mount count reached, running e2fsck is
recommended
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Suspend2: Initrd lacks echo > /proc/suspend2/do_resume.
Freeing unused kernel memory: 220k freed
Adding 769096k swap on /dev/hda2. Priority:-1 extents:1 across:769096k
EXT3 FS on hda1, internal journal
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
(PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level,
high) -> IR
Q 17
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 17, io mem 0xe2080000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 21 (level,
high) -> IR
Q 18
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 18, io mem 0xe2083000
usb 1-2: new full speed USB device using ohci_hcd and address 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@xxxxxxxxxx>
ACPI: PCI Interrupt Link [APCM] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APCM] -> GSI 20 (level,
high) -> IR
Q 19
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e2084000-
e20847ff] Max
Packet=[2048]
Real Time Clock Driver v1.12
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in cold state,
will try to lo
ad a firmware
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
Linux video capture interface: v2.00
cx2388x dvb driver version 0.0.6 loaded
CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T
Dual Digital [
card=44,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:01:09.2[A] -> Link [APC2] -> GSI 17 (level,
high) -> IR
Q 20
cx88[0]/2: found at 0000:01:09.2, rev: 5, irq: 20, latency: 32, mmio:
0xdf000000
cx88[0]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[0]).
DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-2: nForce2 SMBus adapter at 0x5500
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 64M @ 0xd8000000
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level,
high) -> IR
Q 17
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level,
high) -> IR
Q 20
cx88[0]/0: found at 0000:01:09.0, rev: 5, irq: 20, latency: 32, mmio:
0xde000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level,
high) -> IR
Q 18
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 51574 usecs
intel8x0: clocking to 47455
NET: Registered protocol family 17
dvb-usb: did not find the firmware file. (dvb-usb-bluebird-01.fw)
Please see lin
ux/Documentation/dvb/ for more details on firmware-problems. (-2)
dvb_usb_cxusb: probe of 1-2:1.0 failed with error -22
usbcore: registered new driver dvb_usb_cxusb
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bt878: AUDIO driver version 0.0.0 loaded
saa7146: register extension 'dvb'.
saa7146: register extension 'budget dvb'.
saa7146: register extension 'budget_ci dvb'.
saa7146: register extension 'budget_av'.
usbcore: registered new driver ttusb
usbcore: registered new driver ttusb-dec
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Warning: /proc/ide/hd?/settings interface is obsolete, and will be
removed soon!
lirc_dev: IR Remote Control driver registered, at major 61
ts: Compaq touchscreen protocol output
input: PC Speaker as /class/input/input2
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
eth0: no IPv6 routers present
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 20 (level,
high) -> IR
Q 19
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 19, io mem 0xe2086000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
usb 1-2: USB disconnect, address 2
usb 3-2: new high speed USB device using ehci_hcd and address 2
dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in cold state,
will try to lo
ad a firmware
dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw'
usb 3-2: USB disconnect, address 2
dvb-usb: generic DVB-USB module successfully deinitialized and
disconnected.
usb 3-2: new high speed USB device using ehci_hcd and address 3
dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the
software demuxer.
DVB: registering new adapter (DViCO FusionHDTV DVB-T Dual USB).
DVB: registering frontend 1 (Zarlink MT352 DVB-T)...
input: IR-receiver inside an USB DVB receiver as /class/input/input3
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: DViCO FusionHDTV DVB-T Dual USB successfully initialized and
connected.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
cx2388x blackbird driver version 0.0.6 loaded
nvidia: module license 'NVIDIA' taints kernel.
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level,
high) -> IR
Q 21
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar
22 06:44:
39 PST 2005
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cx88[0]/2: cx8802_timeout
cheers,
brett.
_______________________________________________
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
