Hello,
I've Googled and looked through the archives, and seen many threads on this
topic, but so far none of the solutions have worked for me. I have a Twinhan
VP1025 and I can't get the frontend to work. I've tried different PCI slots,
added/removed PCI cards, adjusted BIOS configuration, and changed the latency
timer. I've used FC5 kernels 2.6.15-1.2054_FC5 and 2.6.16-1.2111_FC5. I've
also tried a vanilla 2.6.16. I've downloaded the most recent drivers from
Mercurial and compiled and installed them (today). So far nothing has worked,
and I always get the same _exact_ error messages.
The interesting dmesg lines:
write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x00)
frontend_init: Could not find a Twinhan DST.
dvb-bt8xx: A frontend driver was not found for device 109e/0878 subsystem
1822/0001
The _write_dst error code of -5 is returned from an i2c function call, but you
already know that.
Any thoughts on what I should do next? Thanks for your help!
Nick Luther
--
lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8361 [KLE133] Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=8 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8361 [KLE133] AGP Bridge (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e4000000-e6ffffff
Prefetchable memory behind bridge: 10000000-100fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev
40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 3
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97
Audio Controller (rev 50)
Subsystem: Realtek Semiconductor Co., Ltd. Unknown device 4710
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at e000 [size=4]
Region 2: I/O ports at e400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture
(rev 11)
Subsystem: Twinhan Technology Co. Ltd VisionPlus DVB card
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e8002000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev
11)
Subsystem: Twinhan Technology Co. Ltd VisionPlus DVB Card
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Biostar Microtech Int'l Corp Unknown device 0039
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at e8001000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 10100000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (prog-if
00 [VGA])
Subsystem: Trident Microsystems CyberBlade/i1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e5800000 (32-bit, non-prefetchable) [size=8M]
Region 1: Memory at e6000000 (32-bit, non-prefetchable) [size=128K]
Region 2: Memory at e5000000 (32-bit, non-prefetchable) [size=8M]
[virtual] Expansion ROM at 10000000 [disabled] [size=64K]
Capabilities: [80] AGP version 1.0
Status: RQ=33 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [90] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
dmesg excerpt:
Linux video capture interface: v1.00
parport_pc: VIA parallel port: io=0x378, irq=7
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
PCI: Via IRQ fixup for 0000:00:07.5, from 5 to 11
PCI: Setting latency timer of device 0000:00:07.5 to 64
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 17
bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 17, latency: 32, mmio: 0xe8002000
bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is
1822:0001
bttv0: using: Twinhan DST + clones [card=113,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00d500ff [init]
bttv0: using tuner=4
bttv0: add subdevice "dvb0"
cyblafb: CyblaFB version 0.62 initializing
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 18
Console: switching to colour frame buffer device 80x25
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low) ->
IRQ 10
PCI: Via IRQ fixup for 0000:00:07.2, from 11 to 10
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 10 (level, low) ->
IRQ 10
PCI: Via IRQ fixup for 0000:00:07.3, from 11 to 10
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: irq 10, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Non-volatile memory driver v1.2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@xxxxxxxxxx
device-mapper: dm-multipath version 1.0.4 loaded
EXT3 FS on hda1, internal journal
Adding 554232k swap on /dev/hda2. Priority:-1 extents:1 across:554232k
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (1983 buckets, 15864 max) - 232 bytes per conntrack
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
ppdev: user-space parallel port driver
ppdev0: registered pardevice
ppdev0: unregistered pardevice
ppdev1: claim the port first
ppdev2: claim the port first
ppdev3: claim the port first
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:00:09.1[A] -> GSI 17 (level, low) -> IRQ 17
bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB functions.
bt878(0): Bt878 (rev 17) at 00:09.1, irq: 17, latency: 32, memory: 0xe8000000
DVB: registering new adapter (bttv0).
rdc_8820_reset: Resetting DST
dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000]
dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004]
dst_comm_init: Initializing DST.
dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000]
rdc_reset_state: Resetting state machine
dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000]
dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002]
writing [ 00 06 00 00 00 00 00 fa ]
write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x00)
dst_error_recovery: Trying to return from previous errors.
dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000]
dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000]
write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x00)
dst_error_recovery: Trying to return from previous errors.
dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000]
dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000]
write_dst: RDC 8820 RESET
dst_error_bailout: Trying to bailout from previous error.
rdc_8820_reset: Resetting DST
dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000]
dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004]
dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000]
dst_probe: unknown device.
frontend_init: Could not find a Twinhan DST.
dvb-bt8xx: A frontend driver was not found for device 109e/0878 subsystem
1822/0001
Relevant modprobe.conf lines:
options dst verbose=4
options bttv card=0x71 i2c_hw=1
alias char-major-81 bttv
ls /dev/dvb/adapter0
total 0
crw-rw---- 1 root root 212, 4 May 20 20:22 demux0
crw-rw---- 1 root root 212, 5 May 20 20:22 dvr0
crw-rw---- 1 root root 212, 7 May 20 20:22 net0
_______________________________________________
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
