On Sat, 2006-04-08 at 16:12 +0200, Peter Fassberg wrote: > Hi all! > > I'm using a few Twinhan cards with success. > > However, today I tried to install a new Twinhan DVB-T (w/CI) card and > a new linux kernel but it won't work. > > The driver can't find the frontend, and there are some comments > about Hauppauge IR but there is no Hauppauge card in the box... > > Kernel 2.6.16.1. > > It seems that the problem is that "dst_probe" don't find the card. try modprobe dvb_bt8xx; rmmod dvb_bt8xx;modprobe dvb_bt8xx. Some of the twinhan cards fail to properly initialize at bootup some times, and this workaround often fixes that. > > What is "DST" ? It is a microchip used on most twinhan cards out this far. Regards Sigmund > > I've seen exactly the same question on this list earlier, but I can't > find any answers. > > > Any suggestions? > > > > Best regards, > > > -- Peter Fassberg > Sweden > > > > > dmesg: > ---------------------------------------------------------------------- > Linux video capture interface: v1.00 > bttv: driver version 0.9.16 loaded > bttv: using 8 buffers with 2080k (520 pages) each for capture > bttv: Bt8xx card found (0). > PCI: Found IRQ 5 for device 0000:00:0a.0 > PCI: Sharing IRQ 5 with 0000:00:07.5 > PCI: Sharing IRQ 5 with 0000:00:0a.1 > bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 5, latency: 32, mmio: 0xeb002000 > bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001 > bttv0: using: Twinhan DST + clones [card=113,autodetected] > bttv0: gpio: en=00000000, out=00000000 in=00f500fd [init] > bttv0: using tuner=4 > bttv0: add subdevice "dvb0" > input: i2c IR (Hauppauge) as /class/input/input0 > ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-001a/ir0 [bt878 #0 [hw]] > saa7146: register extension 'budget dvb'. > saa7146: register extension 'budget_ci dvb'. > bt878: AUDIO driver version 0.0.0 loaded > bt878: Bt878 AUDIO function found (0). > PCI: Found IRQ 5 for device 0000:00:0a.1 > PCI: Sharing IRQ 5 with 0000:00:07.5 > PCI: Sharing IRQ 5 with 0000:00:0a.0 > bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB functions. > bt878(0): Bt878 (rev 17) at 00:0a.1, irq: 5, latency: 32, memory: 0xeb000000 > DVB: registering new adapter (bttv0). > i2c IR (Hauppauge): unknown key: key=0x3f raw=0x3fff down=1 > dst_probe: unknown device. > frontend_init: Could not find a Twinhan DST. > dvb-bt8xx: A frontend driver was not found for device 109e/0878 subsystem 1822/0001 > ---------------------------------------------------------------------- > > lspci -vvv: > ---------------------------------------------------------------------- > 0000:00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) > Subsystem: Twinhan Technology Co. Ltd VisionPlus DVB card > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (4000ns min, 10000ns max) > Interrupt: pin A routed to IRQ 5 > Region 0: Memory at eb002000 (32-bit, prefetchable) [size=4K] > Capabilities: <available only to root> > > 0000:00:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) > Subsystem: Twinhan Technology Co. Ltd VisionPlus DVB Card > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (1000ns min, 63750ns max) > Interrupt: pin A routed to IRQ 5 > Region 0: Memory at eb000000 (32-bit, prefetchable) [size=4K] > Capabilities: <available only to root> > ---------------------------------------------------------------------- > > > _______________________________________________ > > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb _______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
