Unfortunately it was not such a brilliant idea I tried the one with mercurian but now even my trusty Nova-T stopped working ediabox ~ # modprobe cx88xx WARNING: Error inserting videodev (/lib/modules/2.6.15.1/kernel/drivers/media/video/videodev.ko): Input/output error mediabox ~ # modprobe cx8800 WARNING: Error inserting videodev (/lib/modules/2.6.15.1/kernel/drivers/media/video/videodev.ko): Input/output error This is what I get in dmesg: ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 5 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 55778 usecs intel8x0: clocking to 48000 Linux video capture interface: v1.00 video_dev: unable to get major 81 i2c-core: driver [tveeprom] registered Linux video capture interface: v1.00 video_dev: unable to get major 81 kobject_register failed for v4l1_compat (-17) [<c0288a1b>] kobject_register+0x6b/0x80 [<c01344a0>] mod_sysfs_setup+0x50/0xc0 [<c0135842>] load_module+0x972/0xab0 [<c014fdd2>] __handle_mm_fault+0x142/0x290 [<c0135a15>] sys_init_module+0x65/0x210 [<c01032c5>] syscall_call+0x7/0xb cx2388x v4l2 driver version 0.0.5 loaded ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5 ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5 CORE cx88[0]: subsystem: 0070:9002, board: Hauppauge Nova-T DVB-T [card=18,autodetected] TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe i2c_adapter i2c-0: adapter [cx88[0]] registered i2c_adapter i2c-0: master_xfer[0] W, addr=0x50, len=1 i2c_adapter i2c-0: master_xfer[0] R, addr=0x50, len=256 tveeprom 0-0050: Hauppauge model 90002, rev C176, serial# 83189 tveeprom 0-0050: MAC address is 00-0D-FE-01-44-F5 tveeprom 0-0050: tuner model is Thompson DTT7592 (idx 76, type 4) tveeprom 0-0050: TV standards ATSC/DVB Digital (eeprom 0x80) tveeprom 0-0050: audio processor is None (idx 0) tveeprom 0-0050: decoder processor is CX882 (idx 25) tveeprom 0-0050: has no radio, has IR remote cx88[0]: hauppauge eeprom: model=90002 input: cx88 IR (Hauppauge Nova-T DVB-T as /class/input/input2 cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 5, latency: 64, mmio: 0xfb000000 cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 kobject_register failed for dvb_pll (-17) [<c0288a1b>] kobject_register+0x6b/0x80 [<c01344a0>] mod_sysfs_setup+0x50/0xc0 [<c0135842>] load_module+0x972/0xab0 [<c014fdd2>] __handle_mm_fault+0x142/0x290 [<c0135a15>] sys_init_module+0x65/0x210 [<c01032c5>] syscall_call+0x7/0xb kobject_register failed for dvb_core (-17) [<c0288a1b>] kobject_register+0x6b/0x80 [<c01344a0>] mod_sysfs_setup+0x50/0xc0 [<c0135842>] load_module+0x972/0xab0 [<c014fdd2>] __handle_mm_fault+0x142/0x290 [<c0135a15>] sys_init_module+0x65/0x210 [<c01032c5>] syscall_call+0x7/0xb Linux video capture interface: v1.00 video_dev: unable to get major 81 cx88_dvb: Unknown symbol dvb_pll_thomson_fe6600 cx88_dvb: Unknown symbol dvb_pll_thomson_dtt761x If I try modprobe saa7134 I get following: mediabox ~ # modprobe saa7134 WARNING: Error inserting videodev (/lib/modules/2.6.15.1/kernel/drivers/media/video/videodev.ko): Input/output error mediabox ~ # dmesg red new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:0b: ioport range 0x680-0x6ff has been reserved pnp: 00:0b: ioport range 0x295-0x296 has been reserved PCI: Bridge: 0000:00:08.0 IO window: disabled. MEM window: f8a00000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: f4900000-f89fffff PREFETCH window: c4800000-e47fffff PCI: Setting latency timer of device 0000:00:08.0 to 64 Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1144098342.700:1): initialized Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). NTFS driver 2.1.25 [Flags: R/W DEBUG]. JFS: nTxBlock = 4016, nTxLock = 32128 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Processor [CPU1] (supports 8 throttling states) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found lp: driver loaded but no devices found Linux agpgart interface v0.101 (c) Dave Jones [drm] Initialized drm 1.0.0 20040925 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)] lp0: using parport0 (interrupt-driven). FDC 0 is a post-1991 82077 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48. ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 3 PCI: setting IRQ 3 as level-triggered ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LKLN] -> GSI 3 (level, low) -> IRQ 3 PCI: Setting latency timer of device 0000:00:04.0 to 64 eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0 PPP generic driver version 2.4.2 NET: Registered protocol family 24 Linux video capture interface: v1.00 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 Loading Adaptec I2O RAID: Version 2.4 Build 5go Detecting Adaptec I2O RAID controllers... ipr: IBM Power RAID SCSI Device Driver version: 2.1.0 (October 31, 2005) libata version 1.20 loaded. sata_nv 0000:00:0b.0: version 0.8 ACPI: PCI Interrupt Link [LSHD] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LSHD] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:0b.0 to 64 ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE882 bmdma 0x7F00 irq 11 ata2: SATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma 0x7F08 irq 11 ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3e01 87:4023 88:407f ata1: dev 0 ATA-7, max UDMA/133, 488397168 sectors: LBA48 nv_sata: Primary device added nv_sata: Primary device removed nv_sata: Secondary device removed ata1: dev 0 configured for UDMA/133 scsi0 : sata_nv ata2: no device found (phy stat 00000000) scsi1 : sata_nv Vendor: ATA Model: WDC WD2500JS-55N Rev: 10.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) SCSI device sda: drive cache: write back SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 ieee1394: raw1394: /dev/raw1394 device initialized usbmon: debugfs is not available ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: EHCI Host Controller ehci_hcd 0000:00:02.2: debug port 0 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.2: irq 5, io mem 0xfebfdc00 ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v2.3 usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27) usbcore: registered new driver rtl8150 usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for PocketPC PDA drivers/usb/serial/ipaq.c: USB PocketPC PDA driver v0.5 usbcore: registered new driver ipaq mice: PS/2 mouse device common for all mice wbsd: Winbond W83L51xD SD/MMC card interface driver, 1.5 wbsd: Copyright(c) Pierre Ossman oprofile: using timer interrupt. NET: Registered protocol family 2 input: AT Translated Set 2 keyboard as /class/input/input0 IP route cache hash table entries: 8192 (order: 3, 32768 bytes) TCP established hash table entries: 32768 (order: 5, 131072 bytes) TCP bind hash table entries: 32768 (order: 5, 131072 bytes) TCP: Hash tables configured (established 32768 bind 32768) TCP reno registered ip_conntrack version 2.4 (4094 buckets, 32752 max) - 212 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost <sfrost@xxxxxxxxxxx>. http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ACPI wakeup devices: PCI0 PS2K PS2M UAR1 MAC AC97 MDM USB0 USB1 USB2 PCI1 ACPI: (supports S0 S1 S3 S4 S5) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 180k freed input: ImPS/2 Generic Wheel Mouse as /class/input/input1 Adding 506036k swap on /dev/sda2. Priority:-1 extents:1 across:506036k EXT3 FS on sda3, internal journal nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:22:51 PST 2005 ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 5 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 55778 usecs intel8x0: clocking to 48000 Linux video capture interface: v1.00 video_dev: unable to get major 81 i2c-core: driver [tveeprom] registered Linux video capture interface: v1.00 video_dev: unable to get major 81 kobject_register failed for v4l1_compat (-17) [<c0288a1b>] kobject_register+0x6b/0x80 [<c01344a0>] mod_sysfs_setup+0x50/0xc0 [<c0135842>] load_module+0x972/0xab0 [<c014fdd2>] __handle_mm_fault+0x142/0x290 [<c0135a15>] sys_init_module+0x65/0x210 [<c01032c5>] syscall_call+0x7/0xb cx2388x v4l2 driver version 0.0.5 loaded ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5 ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5 CORE cx88[0]: subsystem: 0070:9002, board: Hauppauge Nova-T DVB-T [card=18,autodetected] TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe i2c_adapter i2c-0: adapter [cx88[0]] registered i2c_adapter i2c-0: master_xfer[0] W, addr=0x50, len=1 i2c_adapter i2c-0: master_xfer[0] R, addr=0x50, len=256 tveeprom 0-0050: Hauppauge model 90002, rev C176, serial# 83189 tveeprom 0-0050: MAC address is 00-0D-FE-01-44-F5 tveeprom 0-0050: tuner model is Thompson DTT7592 (idx 76, type 4) tveeprom 0-0050: TV standards ATSC/DVB Digital (eeprom 0x80) tveeprom 0-0050: audio processor is None (idx 0) tveeprom 0-0050: decoder processor is CX882 (idx 25) tveeprom 0-0050: has no radio, has IR remote cx88[0]: hauppauge eeprom: model=90002 input: cx88 IR (Hauppauge Nova-T DVB-T as /class/input/input2 cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 5, latency: 64, mmio: 0xfb000000 cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 kobject_register failed for dvb_pll (-17) [<c0288a1b>] kobject_register+0x6b/0x80 [<c01344a0>] mod_sysfs_setup+0x50/0xc0 [<c0135842>] load_module+0x972/0xab0 [<c014fdd2>] __handle_mm_fault+0x142/0x290 [<c0135a15>] sys_init_module+0x65/0x210 [<c01032c5>] syscall_call+0x7/0xb kobject_register failed for dvb_core (-17) [<c0288a1b>] kobject_register+0x6b/0x80 [<c01344a0>] mod_sysfs_setup+0x50/0xc0 [<c0135842>] load_module+0x972/0xab0 [<c014fdd2>] __handle_mm_fault+0x142/0x290 [<c0135a15>] sys_init_module+0x65/0x210 [<c01032c5>] syscall_call+0x7/0xb Linux video capture interface: v1.00 video_dev: unable to get major 81 cx88_dvb: Unknown symbol dvb_pll_thomson_fe6600 cx88_dvb: Unknown symbol dvb_pll_thomson_dtt761x spurious 8259A interrupt: IRQ15. Linux video capture interface: v1.00 video_dev: unable to get major 81 i2c-core: driver [ir-kbd-i2c] registered kobject_register failed for v4l1_compat (-17) [<c0288a1b>] kobject_register+0x6b/0x80 [<c01344a0>] mod_sysfs_setup+0x50/0xc0 [<c0135842>] load_module+0x972/0xab0 [<c014fdd2>] __handle_mm_fault+0x142/0x290 [<c0135a15>] sys_init_module+0x65/0x210 [<c01032c5>] syscall_call+0x7/0xb saa7130/34: v4l2 driver version 0.2.14 loaded ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5 ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5 saa7133[0]: found at 0000:02:09.0, rev: 208, irq: 5, latency: 64, mmio: 0xfeadf800 saa7133[0]: subsystem: 17de:7201, board: Tevion/KWorld DVB-T 220RF [card=88,autodetected] saa7133[0]: board init: gpio is 100 i2c_adapter i2c-1: adapter [saa7133[0]] registered i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50 i2c_adapter i2c-1: master_xfer[0] W, addr=0x50, len=0 i2c_adapter i2c-1: master_xfer[0] W, addr=0x50, len=0 i2c_adapter i2c-1: client [tveeprom] registered with bus id 1-0050 i2c_adapter i2c-1: master_xfer[0] R, addr=0x7a, len=0 i2c_adapter i2c-1: master_xfer[0] R, addr=0x47, len=0 i2c_adapter i2c-1: master_xfer[0] W, addr=0x50, len=1 i2c_adapter i2c-1: master_xfer[0] R, addr=0x50, len=128 saa7133[0]: i2c eeprom 00: de 17 01 72 ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff i2c_adapter i2c-1: master_xfer[0] W, addr=0x08, len=3 i2c-core: driver [tuner] registered i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x42 i2c_adapter i2c-1: master_xfer[0] W, addr=0x42, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x43 i2c_adapter i2c-1: master_xfer[0] W, addr=0x43, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x4a i2c_adapter i2c-1: master_xfer[0] W, addr=0x4a, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x4b i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=0 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=1 i2c_adapter i2c-1: master_xfer[0] R, addr=0x4b, len=1 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=1 i2c_adapter i2c-1: master_xfer[0] R, addr=0x4b, len=1 tuner 1-004b: chip found @ 0x96 (saa7133[0]) i2c_adapter i2c-1: client [(tuner unset)] registered with bus id 1-004b i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] R, addr=0x60, len=1 i2c_adapter i2c-1: master_xfer[0] R, addr=0x61, len=1 i2c_adapter i2c-1: master_xfer[0] R, addr=0x62, len=1 i2c_adapter i2c-1: master_xfer[0] R, addr=0x63, len=1 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 tuner 1-004b: setting tuner address to 61 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] R, addr=0x61, len=1 tuner 1-004b: type set to tda8290+75a i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] W, addr=0x61, len=14 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x60 i2c_adapter i2c-1: master_xfer[0] W, addr=0x60, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x61 i2c_adapter i2c-1: master_xfer[0] W, addr=0x61, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x62 i2c_adapter i2c-1: master_xfer[0] W, addr=0x62, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x63 i2c_adapter i2c-1: master_xfer[0] W, addr=0x63, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x64 i2c_adapter i2c-1: master_xfer[0] W, addr=0x64, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x65 i2c_adapter i2c-1: master_xfer[0] W, addr=0x65, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x66 i2c_adapter i2c-1: master_xfer[0] W, addr=0x66, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x67 i2c_adapter i2c-1: master_xfer[0] W, addr=0x67, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x68 i2c_adapter i2c-1: master_xfer[0] W, addr=0x68, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x69 i2c_adapter i2c-1: master_xfer[0] W, addr=0x69, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6a i2c_adapter i2c-1: master_xfer[0] W, addr=0x6a, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6b i2c_adapter i2c-1: master_xfer[0] W, addr=0x6b, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6c i2c_adapter i2c-1: master_xfer[0] W, addr=0x6c, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6d i2c_adapter i2c-1: master_xfer[0] W, addr=0x6d, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6e i2c_adapter i2c-1: master_xfer[0] W, addr=0x6e, len=0 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6f i2c_adapter i2c-1: master_xfer[0] W, addr=0x6f, len=0 saa7133[0]: registered device video1 [v4l2] saa7133[0]: registered device vbi1 saa7133[0]: registered device radio0 > This card works with the CVS version, the card also works with the latest > git kernel from > kernel.org. > > The remote as yet doesn't work. > > > Jyrki Majamaki wrote: >> I have Kworld DVB-T 220 and it is evil. It's aDVB-T card >> with analogue tuner as well. >> >> lspci: >> >> 02:09.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 >> Video >> Broadcast Decoder (rev d0) >> >> Following kernel modules at least sound related: >> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa6752hs.ko >> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa7134-alsa.ko >> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa7134-dvb.ko >> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa7134-empress.ko >> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa7134.ko >> >> Ok first modprobe saa7134: >> i2c-core: driver [ir remote kbd driver] registered >> saa7130/34: v4l2 driver version 0.2.14 loaded >> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5 >> ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 5 (level, low) >> -> >> IRQ 5 >> saa7133[0]: found at 0000:02:09.0, rev: 208, irq: 5, latency: 64, mmio: >> 0xfeadf800 >> saa7133[0]: subsystem: 17de:7201, board: UNKNOWN/GENERIC >> [card=0,autodetected] >> saa7133[0]: board init: gpio is 100 >> i2c_adapter i2c-1: adapter [saa7133[0]] registered >> i2c_adapter i2c-1: master_xfer[0] R, addr=0x7a, len=0 >> i2c_adapter i2c-1: master_xfer[0] R, addr=0x47, len=0 >> i2c_adapter i2c-1: master_xfer[0] W, addr=0x50, len=1 >> i2c_adapter i2c-1: master_xfer[0] R, addr=0x50, len=128 >> saa7133[0]: i2c eeprom 00: de 17 01 72 ff ff ff ff ff ff ff ff ff ff ff >> ff >> saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> ff >> saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> ff >> saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> ff >> saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> ff >> saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> ff >> saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> ff >> saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> ff >> saa7133[0]: registered device video1 [v4l2] >> saa7133[0]: registered device vbi1 >> >> modprobe saa7134-empress: >> nothing >> >> modprobe saa6725hs: >> i2c-core: driver [i2c saa6752hs MPEG encoder] registered >> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x20 >> i2c_adapter i2c-1: master_xfer[0] W, addr=0x20, len=0 >> >> modprobe saa7134-dvb: >> nothing (unfortunately I guess) >> >> modprobe saa7134-alsa: >> saa7134 ALSA driver for DMA sound loaded >> saa7133[0]/alsa: saa7133[0] at 0xfeadf800 irq 5 registered as card -1 >> >> I don't know what this alsa is looking in that card for...there is also >> a >> radio tuner there so maybe >> something to do with it... >> >> lsmod looks like: >> Module Size Used by >> saa7134_alsa 10912 0 >> saa7134_dvb 10372 0 >> tda1004x 15172 1 saa7134_dvb >> saa6752hs 8460 0 >> saa7134_empress 7108 0 >> saa7134 109728 3 saa7134_alsa,saa7134_dvb,saa7134_empress >> ir_kbd_i2c 6604 1 saa7134 >> snd_pcm_oss 49696 0 >> snd_mixer_oss 17152 1 snd_pcm_oss >> snd_seq_oss 32320 0 >> snd_seq_midi_event 6080 1 snd_seq_oss >> snd_seq 50128 4 snd_seq_oss,snd_seq_midi_event >> snd_seq_device 6860 2 snd_seq_oss,snd_seq >> snd_intel8x0 29596 0 >> snd_ac97_codec 92384 1 snd_intel8x0 >> snd_ac97_bus 1792 1 snd_ac97_codec >> snd_pcm 82824 4 saa7134_alsa,snd_pcm_oss,snd_intel8x0,snd_ac97_codec >> snd_timer 22084 2 snd_seq,snd_pcm >> snd 47076 10 >> saa7134_alsa,snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer >> soundcore 7840 1 snd >> snd_page_alloc 8456 2 snd_intel8x0,snd_pcm >> cx88_dvb 7684 0 >> mt352 6212 2 saa7134_dvb,cx88_dvb >> or51132 9284 1 cx88_dvb >> video_buf_dvb 4548 2 saa7134_dvb,cx88_dvb >> nxt200x 14724 2 saa7134_dvb,cx88_dvb >> lgdt330x 7708 1 cx88_dvb >> cx22702 6020 1 cx88_dvb >> cx8802 9220 1 cx88_dvb >> cx8800 28300 0 >> cx88xx 55712 3 cx88_dvb,cx8802,cx8800 >> video_buf 17284 9 >> saa7134_alsa,saa7134_dvb,saa7134_empress,saa7134,cx88_dvb,video_buf_dvb,cx8802,cx8800,cx88xx >> ir_common 8132 3 saa7134,ir_kbd_i2c,cx88xx >> btcx_risc 3976 3 cx8802,cx8800,cx88xx >> tveeprom 13776 1 cx88xx >> nvidia 4083664 12 >> >> I could try modprobe with different card options but I am not sure >> whether >> this is going to help other than with analogue tuner. >> >> The mentioned cx88 modules come from my second card Hauppage Nova-T >> (works >> like a charm) >> >> >> _______________________________________________ >> >> linux-dvb@xxxxxxxxxxx >> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >> >> >> > > > _______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
