Hi,
I have been struggling for the past few days trying to get an Artec T1 working correctly under Linux (Slackware 10.2).
I have tried various flavours of kernel from 2.6.13 to 2.6.16.1 with the standard kernel DVB drivers, and various versions of dvb-kernel from CVS without any luck.
When the box is plugged in, "lsusb -vvv" reports the following:
Bus 003 Device 003: ID 05d8:8107 Ultima Electronics Corp. Artec T1 USB TVBOX with AN2235 (cold)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x05d8 Ultima Electronics Corp.
idProduct 0x8107 Artec T1 USB TVBOX with AN2235 (cold)
bcdDevice 0.01
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
...
...
As this lists the device as having the AN2235 USB controller, I am using the dvb-usb-dibusb-an2235-01.fw (md5sum=e7a05363c7ed4d9b78cbedd767c7acfe) firmware, which I have placed in /lib/firmware.
The drivers compile and load without any problems, but as soon as the box is attached to the computer dmesg starts filling up with:
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
..
..
/var/log/messages reports the following:
Apr 3 15:54:25 magpie kernel: usb 3-1: new full speed USB device using uhci_hcd and address 3
Apr 3 15:54:25 magpie kernel: dvb-usb: found a 'Artec T1 USB1.1 TVBOX with AN2235' in warm state.
Apr 3 15:54:25 magpie kernel: dvb-usb: will use the device's hardware PID filter (table count: 16).
Apr 3 15:54:25 magpie kernel: dibusb: this device has the Panasonic ENV77H11D5 onboard.
Apr 3 15:54:25 magpie kernel: dvb-usb: schedule remote query interval to 150 msecs.
Apr 3 15:54:25 magpie kernel: dvb-usb: Artec T1 USB1.1 TVBOX with AN2235 successfully initialized and connected.
This seems to suggest that everything should be working OK, and yet the LEDs do not come on (indicating that the firmware has not been correctly loaded), and no /dev/dvb.frontend0 device is created by udev (/dev/dvb0.demux0, /dev/dvb0.dvr0 and /dev/dvb0/net0 are created at this point) .
I have tried many things including uncommenting the "#define DVB_USB_DIBUSB_MB_FAULTY_USB_IDs" line in dvb-kernel/linux/drivers/media/dvb/dvb-usb/dibusb-mb.c, as described in the Artec T1 howto, here - http://linuxtv.org/wiki/index.php/Artec_T1_USB_TV_Box, without any luck.
I have also tried (just to make sure that the hardware actually works at all) running it under windows, and frustratingly it fires up first time without any problems :(. However, one thing that I did notice from this is that the windows drivers report the product ID to be 8108 rather than 8107 (as reported by lsusb under Linux). I'm not sure if this is important, but thought I'd mention it, just in case.
I would be very grateful for any suggestions that you have, even if it is just to say that this type of T1 isn't currently supported, as at least then I can move on, or buy some new hardware.
Many thanks
I have been struggling for the past few days trying to get an Artec T1 working correctly under Linux (Slackware 10.2).
I have tried various flavours of kernel from 2.6.13 to 2.6.16.1 with the standard kernel DVB drivers, and various versions of dvb-kernel from CVS without any luck.
When the box is plugged in, "lsusb -vvv" reports the following:
Bus 003 Device 003: ID 05d8:8107 Ultima Electronics Corp. Artec T1 USB TVBOX with AN2235 (cold)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x05d8 Ultima Electronics Corp.
idProduct 0x8107 Artec T1 USB TVBOX with AN2235 (cold)
bcdDevice 0.01
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
...
...
As this lists the device as having the AN2235 USB controller, I am using the dvb-usb-dibusb-an2235-01.fw (md5sum=e7a05363c7ed4d9b78cbedd767c7acfe) firmware, which I have placed in /lib/firmware.
The drivers compile and load without any problems, but as soon as the box is attached to the computer dmesg starts filling up with:
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
dvb-usb: bulk message failed: -90 (1/0)
..
..
/var/log/messages reports the following:
Apr 3 15:54:25 magpie kernel: usb 3-1: new full speed USB device using uhci_hcd and address 3
Apr 3 15:54:25 magpie kernel: dvb-usb: found a 'Artec T1 USB1.1 TVBOX with AN2235' in warm state.
Apr 3 15:54:25 magpie kernel: dvb-usb: will use the device's hardware PID filter (table count: 16).
Apr 3 15:54:25 magpie kernel: dibusb: this device has the Panasonic ENV77H11D5 onboard.
Apr 3 15:54:25 magpie kernel: dvb-usb: schedule remote query interval to 150 msecs.
Apr 3 15:54:25 magpie kernel: dvb-usb: Artec T1 USB1.1 TVBOX with AN2235 successfully initialized and connected.
This seems to suggest that everything should be working OK, and yet the LEDs do not come on (indicating that the firmware has not been correctly loaded), and no /dev/dvb.frontend0 device is created by udev (/dev/dvb0.demux0, /dev/dvb0.dvr0 and /dev/dvb0/net0 are created at this point) .
I have tried many things including uncommenting the "#define DVB_USB_DIBUSB_MB_FAULTY_USB_IDs" line in dvb-kernel/linux/drivers/media/dvb/dvb-usb/dibusb-mb.c, as described in the Artec T1 howto, here - http://linuxtv.org/wiki/index.php/Artec_T1_USB_TV_Box, without any luck.
I have also tried (just to make sure that the hardware actually works at all) running it under windows, and frustratingly it fires up first time without any problems :(. However, one thing that I did notice from this is that the windows drivers report the product ID to be 8108 rather than 8107 (as reported by lsusb under Linux). I'm not sure if this is important, but thought I'd mention it, just in case.
I would be very grateful for any suggestions that you have, even if it is just to say that this type of T1 isn't currently supported, as at least then I can move on, or buy some new hardware.
Many thanks
Richard
_______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
