Yea- i assumed it used stv0299, which is loaded with the b2c2-flexcop
driver.It just doesnt probe/attach/whatever correctly.
:
% lsmod
<clip>
b2c2_flexcop_pci 8984 0
b2c2_flexcop 25292 1 b2c2_flexcop_pci
mt352 8580 1 b2c2_flexcop
mt312 9412 1 b2c2_flexcop
bcm3510 11332 1 b2c2_flexcop
stv0299 12552 1 b2c2_flexcop
dvb_core 81436 2 b2c2_flexcop,stv0299
nxt200x 15300 1 b2c2_flexcop
firmware_class 11008 5 cx25840,tuner,b2c2_flexcop,bcm3510,nxt200x
dvb_pll 13252 2 b2c2_flexcop,nxt200x
stv0297_cs2 11588 1 b2c2_flexcop
lgdt330x 9884 1 b2c2_flexcop
i2c_core 21632 14
tda9887,wm8775,cx25840,tuner,tveeprom,i2c_algo_
bit,b2c2_flexcop,mt352,mt312,bcm3510,stv0299,nxt200x,stv0297_cs2,lgdt330x
<clip>
I'm going to take out my pvr150's, see if thats confusing things.
-brendan
Nico Sabbi wrote:
Brendan White wrote:
SkyStar2 TV version 2.6D
gentoo amd64
2.6.14
I've tried stock 2.6.14 drivers, linuxtv stable snapshot, and the
most recent daily snapshot. I've tried the card in different
slots. All yield the same results. The frontend driver modules do
load, they just dont seem to do anything useful:
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip
loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC4] -> GSI 19 (level,
low) -> IRQ 66
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: reading of MAC address failed.
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
mt352_read_register: readreg error (reg=127, ret==-121)
b2c2-flexcop: i2c master_xfer failed
nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
Unknown/Unsupported NXT chip: 00 00 00 00 00
b2c2-flexcop: i2c master_xfer failed
lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret ==
-121)
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
mt312_read: ret == -121
b2c2-flexcop: no frontend driver found for this B2C2/FlexCop adapter
ACPI: PCI interrupt for device 0000:01:09.0 disabled
doesn't this card use the stv0299?
_______________________________________________
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
