Hello.
I am running FC3 with the dvb drivers that came with the installation. Not sure why the dvb directories are not created under /dev at startup by udev. Everything seems to load fine for the dvb driver and I do have the udev rules for dvb after upgrading to the recent udev version. Any feedback on this matter would be appreciated.
Regards.
-Ryan
# lspci -v
00:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend/Hauppauge DVB card rev2.1
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ffeff800 (32-bit, non-prefetchable) [size=512]
# lsmod
ipv6 232577 8
uhci_hcd 31449 0
dvb_ttpci 80517 0
dvb_core 86121 1 dvb_ttpci
saa7146_vv 44865 1 dvb_ttpci
video_buf 21701 1 saa7146_vv
saa7146 17805 2 dvb_ttpci,saa7146_vv
v4l1_compat 11973 1 saa7146_vv
v4l2_common 5953 1 saa7146_vv
videodev 9664 1 saa7146_vv
ttpci_eeprom 2497 1 dvb_ttpci
# dmesg
Linux video capture interface: v1.00
saa7146: register extension 'dvb'.
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 10 (level, low) -> IRQ 10
saa7146: found saa7146 @ mem 1083c800 (revision 1, irq 10) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge PCI rev2.1).
Technotrend/Hauppauge PCI rev2.1 adapter 0 has MAC addr = 00:d0:5c:23:6f:1c
gpioirq unknown type=0 len=0
DVB: AV7110(0) - firm f0240009, rtsl b0250018, vid 71010068, app 80002622
DVB: AV7110(0) - firmware supports CI link layer interface
av7110(0): Crystal audio DAC detected
videodev: "av7110" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
av7110: found av7110-0.
# cat /etc/udev/rules.d/50-udev.rules
KERNEL="dvb" Name="dvb0"
KERNEL="dvb0.dvr*", NAME="dvb/adapter0/dvr%n"
KERNEL="dvb0.demux*", NAME="dvb/adapter0/demux%n"
KERNEL="dvb0.frontend*", NAME="dvb/adapter0/frontend%n"
KERNEL="dvb0.audio*", NAME="dvb/adapter0/audio%n"
KERNEL="dvb0.ca*", NAME="dvb/adapter0/ca%n"
KERNEL="dvb0.osd*", NAME="dvb/adapter0/osd%n"
KERNEL="dvb0.net*", NAME="dvb/adapter0/net%n"
KERNEL="dvb0.video*", NAME="dvb/adapter0/video%n"
etc.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20060122/d9146014/attachment.htm
