Hi, Peter Hi, Hartmut Thanks for rolling the ball Peter I have been looking at this on the weekend I too have just purchased this card and also have it using (card 81 but with tuner=54) and dvb module loaded. The card does not scan on analog for me however it does manually tune if i pick a channel. The card did output 1 dvb channel for myself but it cannot scan or manually tune. The way I can get the card on 1 channel is a bit harsh: I boot into windows and use the mediaportal opensource program which knows the card. (its a kworld dvbt-220 equivalent) then if i select close full screen the program crashes leaving the card on the last frequency. Then I reboot to linux without powering off and the card is still on the last dvb frequency ! The card then will only run if i pick that same frequency with a dvb application on linux. some logs: saa7130/34: v4l2 driver version 0.2.14 loaded ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 20 saa7133[0]: found at 0000:01:0a.0, rev: 208, irq: 20, latency: 32, mmio: 0xea003000 saa7133[0]: subsystem: 17de:7201, board: Philips Tiger reference design [card=81,insmod option] saa7133[0]: board init: gpio is 100 saa7133[0]: i2c eeprom 00: de 17 01 72 ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tuner 0-004b: chip found @ 0x96 (saa7133[0]) tuner 0-004b: setting tuner address to 61 tuner 0-004b: tuner: type set to tda8290+75a saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 DVB: registering new adapter (saa7133[0]). DVB: registering frontend 0 (Philips TDA10046H DVB-T)... I get this output from VLC set to a channel: main debug: `dvb:' gives access `dvb' demux `' path `' main debug: creating demux: access='dvb' demux='' path='' main debug: looking for access_demux module: 0 candidates main warning: no access_demux module matched "dvb" main debug: creating access 'dvb' path='' main debug: looking for access2 module: 8 candidates dvb debug: Opening device /dev/dvb/adapter0/frontend0 dvb debug: Frontend Info: dvb debug: name = Philips TDA10046H DVB-T dvb debug: type = OFDM (DVB-T) dvb debug: frequency_min = 51000000 (kHz) dvb debug: frequency_max = 858000000 (kHz) dvb debug: frequency_stepsize = 166667 dvb debug: frequency_tolerance = 0 dvb debug: symbol_rate_min = 0 (kHz) dvb debug: symbol_rate_max = 0 (kHz) dvb debug: symbol_rate_tolerance (ppm) = 0 dvb debug: notifier_delay (ms) = 0 dvb debug: Frontend Info capability list: dvb debug: inversion auto dvb debug: forward error correction 1/2 dvb debug: forward error correction 2/3 dvb debug: forward error correction 3/4 dvb debug: forward error correction 5/6 dvb debug: forward error correction 7/8 dvb debug: forward error correction auto dvb debug: card can do QPSK dvb debug: card can do QAM 16 dvb debug: card can do QAM 64 dvb debug: card can do QAM auto dvb debug: transmission mode auto dvb debug: guard interval mode auto dvb debug: End of capability list dvb debug: trying to tune the frontend... dvb debug: using inversion=2 dvb debug: using bandwidth=7 dvb debug: using fec=9 dvb debug: using fec=9 dvb debug: using transmission=0 dvb debug: using guard=0 dvb debug: using hierarchy=0 dvb debug: Opening device /dev/dvb/adapter0/dvr0 dvb debug: setting filter on PAT dvb debug: Opening device /dev/dvb/adapter0/demux0 dvb debug: DMXSetFilter: DMX_PES_OTHER for PID 0 dvb debug: Opening device /dev/dvb/adapter0/ca0 dvb warning: CAMInit: opening CAM device failed (No such device) main debug: using access2 module "dvb" main debug: pre buffering dvb warning: no lock, tuning again dvb debug: using inversion=2 dvb debug: using bandwidth=7 dvb debug: using fec=9 dvb debug: using fec=9 dvb debug: using transmission=0 dvb debug: using guard=0 dvb debug: using hierarchy=0 dvb warning: no lock, tuning again dvb debug: using inversion=2 dvb debug: using bandwidth=7 dvb debug: using fec=9 dvb debug: using fec=9 dvb debug: using transmission=0 dvb debug: using guard=0 dvb debug: using hierarchy=0 .....and over and over.... whilst the above happens dmesg shows this: tda1004x: found firmware revision 33 -- invalid tda1004x: booting from eeprom tda1004x: found firmware revision 23 -- ok It would be nice to run this card under kaffeine on more than just one channel ;-) thankyou for looking at my post. 73 Brett ____________________________________________________ Do you Yahoo!? Yahoo! Photos: Now with unlimited storage http://au.photos.yahoo.com
