> ---- Vadim Catana <vcatana@xxxxxxxxxxx> wrote: > > es3110@xxxxxxxxxxxx wrote: > > > I still cannot get DVB to work. Dvbsnoop keeps reporting false and/or incorrect signal values. I followed the procedure you did and sttill I am at a loss. > > > > > > What LNBf do you have? Perhaps that might give some clue to the problem? > > > > > > My LNBf: > > > > > > RF: 11.7-12.5GHz > > > IF: 950-1750MHz > > > LO: 10.75GHz > > > > > > > Did you test the dish, LNB, cable with another dvb card or a tuner ? > > I didn't try dvbsnoop, but it works with dvbtune, VDR, mplayer. > > Could you try some other tools like scan and szap from linuxtv.org CVS. > > What messages do you have when you load the drivers ? > > > > Regards, > > Vadim Catana I don't have any other way to test the LNBf, dish or card. However, they are all brand new. Dvbscan does not have any -l settings that match my LNBf at all so I can't really run dvbscan at all. However, if I do run it without any options, all I get is the following: guu-sama scan # ./dvbscan -A 3 -vvv dvb-s/USA/Intelsat5 > /home/banana/.szap/channels.conf scanning dvb-s/USA/Intelsat5 using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 11874000 H 22000000 3 initial transponder 11966000 H 22000000 3 initial transponder 12090000 H 20000000 3 initial transponder 12122000 H 22000000 3 initial transponder 12152000 H 20000000 3 initial transponder 11789000 V 25000000 3 initial transponder 11836000 V 20765000 2 initial transponder 11867000 V 22000000 3 initial transponder 11898000 V 22000000 3 initial transponder 11929000 V 22000000 3 initial transponder 11991000 V 22000000 3 initial transponder 12053000 V 22000000 3 initial transponder 12115000 V 22425000 3 initial transponder 12146000 V 22000000 3 initial transponder 12177000 V 23000000 3 >>> tune to: 11874:h:0:22000 DiSEqC: switch pos 0, 18V, hiband (index 3) diseqc_send_msg:59: DiSEqC: e0 10 38 f3 00 00 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 WARNING: >>> tuning failed!!! >>> tune to: 11874:h:0:22000 (tuning failed) DiSEqC: switch pos 0, 18V, hiband (index 3) diseqc_send_msg:59: DiSEqC: e0 10 38 f3 00 00 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 WARNING: >>> tuning failed!!! >>> tune to: 11966:h:0:22000 DiSEqC: switch pos 0, 18V, hiband (index 3) diseqc_send_msg:59: DiSEqC: e0 10 38 f3 00 00 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >> tuning status == 0x03 >>> tuning status == 0x03 WARNING: >>> tuning failed!!! >>> tune to: 11966:h:0:22000 (tuning failed) DiSEqC: switch pos 0, 18V, hiband (index 3) diseqc_send_msg:59: DiSEqC: e0 10 38 f3 00 00 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 >>> tuning status == 0x03 WARNING: >>> tuning failed!!! >>> tune to: 12090:h:0:20000 DiSEqC: switch pos 0, 18V, hiband (index 3) I haven't tried running dvbscan without the dish plugged in to see if it still gives the same output. Would you like me to?
