Hi list, it is me again. I could not manage to get my pinnacle running with the 2.6.14 kernel until now. Does anybody use the pinnacle 300i with a kernel-version later than 2.6.12? For me the card works fine with the 2.6.12 kernel but I get plenty of I2C errors if I use any newer kernel. This is my /var/log/messages output: [BEGIN /var/log/messages] [...] Dec 29 11:39:41 [ 1835.998374] Linux video capture interface: v1.00 Dec 29 11:39:41 [ 1836.040520] saa7130/34: v4l2 driver version 0.2.14 loaded Dec 29 11:39:41 [ 1836.041521] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 17 Dec 29 11:39:41 [ 1836.041642] saa7134[0]: found at 0000:00:0a.0, rev: 1, irq: 17, latency: 32, mmio: 0xcfffcc00 Dec 29 11:39:41 [ 1836.041704] saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected] Dec 29 11:39:41 [ 1836.041770] saa7134[0]: board init: gpio is c806000 Dec 29 11:39:41 [ 1836.146101] i2c_adapter i2c-0: adapter [saa7134[0]] registered Dec 29 11:39:41 [ 1836.146269] i2c_adapter i2c-0: master_xfer[0] W, addr=0x50, len=1 Dec 29 11:39:41 [ 1836.153201] i2c_adapter i2c-0: master_xfer[0] R, addr=0x50, len=64 Dec 29 11:39:41 [ 1836.168878] saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92 Dec 29 11:39:41 [ 1836.169077] saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff Dec 29 11:39:41 [ 1836.169264] saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff Dec 29 11:39:41 [ 1836.169448] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Dec 29 11:39:41 [ 1836.175206] i2c-core: driver [tuner] registered Dec 29 11:39:41 [ 1836.175215] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x4b Dec 29 11:39:41 [ 1836.175221] i2c_adapter i2c-0: master_xfer[0] W, addr=0x4b, len=0 Dec 29 11:39:41 [ 1836.175357] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x60 Dec 29 11:39:41 [ 1836.175360] i2c_adapter i2c-0: master_xfer[0] W, addr=0x60, len=0 Dec 29 11:39:41 [ 1836.184868] tuner 0-0060: chip found @ 0xc0 (saa7134[0]) Dec 29 11:39:41 [ 1836.184875] i2c_adapter i2c-0: master_xfer[0] R, addr=0x60, len=7 Dec 29 11:39:41 [ 1836.192850] tuner 0-0060: Chip ID is not zero. It is not a TEA5767 Dec 29 11:39:41 [ 1836.192857] i2c_adapter i2c-0: client [(tuner unset)] registered with bus id 0-0060 Dec 29 11:39:41 [ 1836.193862] i2c_adapter i2c-0: master_xfer[0] W, addr=0x60, len=1 Dec 29 11:39:41 [ 1836.200846] i2c_adapter i2c-0: master_xfer[0] R, addr=0x60, len=21 Dec 29 11:39:41 [ 1836.212827] tuner 0-0060: microtune: companycode=3cbf part=42 rev=2f Dec 29 11:39:41 [ 1836.212831] i2c_adapter i2c-0: master_xfer[0] W, addr=0x60, len=2 Dec 29 11:39:41 [ 1836.220817] i2c_adapter i2c-0: master_xfer[0] W, addr=0x60, len=2 Dec 29 11:39:41 [ 1836.228808] i2c_adapter i2c-0: master_xfer[0] W, addr=0x60, len=1 Dec 29 11:39:41 [ 1836.236800] i2c_adapter i2c-0: master_xfer[0] R, addr=0x60, len=1 Dec 29 11:39:41 [ 1836.244791] tuner 0-0060: microtune MT2050 found, OK Dec 29 11:39:41 [ 1836.244797] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x61 Dec 29 11:39:41 [ 1836.244802] i2c_adapter i2c-0: master_xfer[0] W, addr=0x61, len=0 Dec 29 11:39:41 [ 1836.244937] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x62 Dec 29 11:39:41 [ 1836.244940] i2c_adapter i2c-0: master_xfer[0] W, addr=0x62, len=0 Dec 29 11:39:41 [ 1836.245110] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x63 Dec 29 11:39:41 [ 1836.245113] i2c_adapter i2c-0: master_xfer[0] W, addr=0x63, len=0 Dec 29 11:39:41 [ 1836.245283] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x64 Dec 29 11:39:41 [ 1836.245285] i2c_adapter i2c-0: master_xfer[0] W, addr=0x64, len=0 Dec 29 11:39:41 [ 1836.245453] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x65 Dec 29 11:39:41 [ 1836.245456] i2c_adapter i2c-0: master_xfer[0] W, addr=0x65, len=0 Dec 29 11:39:41 [ 1836.245624] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x66 Dec 29 11:39:41 [ 1836.245627] i2c_adapter i2c-0: master_xfer[0] W, addr=0x66, len=0 Dec 29 11:39:41 [ 1836.245795] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x67 Dec 29 11:39:41 [ 1836.245798] i2c_adapter i2c-0: master_xfer[0] W, addr=0x67, len=0 Dec 29 11:39:41 [ 1836.245966] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x68 Dec 29 11:39:41 [ 1836.245969] i2c_adapter i2c-0: master_xfer[0] W, addr=0x68, len=0 Dec 29 11:39:41 [ 1836.246136] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x69 Dec 29 11:39:41 [ 1836.246139] i2c_adapter i2c-0: master_xfer[0] W, addr=0x69, len=0 Dec 29 11:39:41 [ 1836.246307] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x6a Dec 29 11:39:41 [ 1836.246310] i2c_adapter i2c-0: master_xfer[0] W, addr=0x6a, len=0 Dec 29 11:39:41 [ 1836.246478] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x6b Dec 29 11:39:41 [ 1836.246481] i2c_adapter i2c-0: master_xfer[0] W, addr=0x6b, len=0 Dec 29 11:39:41 [ 1836.246649] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x6c Dec 29 11:39:41 [ 1836.246652] i2c_adapter i2c-0: master_xfer[0] W, addr=0x6c, len=0 Dec 29 11:39:41 [ 1836.246829] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x6d Dec 29 11:39:41 [ 1836.246832] i2c_adapter i2c-0: master_xfer[0] W, addr=0x6d, len=0 Dec 29 11:39:41 [ 1836.247000] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x6e Dec 29 11:39:41 [ 1836.247003] i2c_adapter i2c-0: master_xfer[0] W, addr=0x6e, len=0 Dec 29 11:39:41 [ 1836.247171] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x6f Dec 29 11:39:41 [ 1836.247174] i2c_adapter i2c-0: master_xfer[0] W, addr=0x6f, len=0 Dec 29 11:39:41 [ 1836.253402] i2c-core: driver [i2c tda9887 driver] registered Dec 29 11:39:41 [ 1836.253411] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x42 Dec 29 11:39:41 [ 1836.253417] i2c_adapter i2c-0: master_xfer[0] W, addr=0x42, len=0 Dec 29 11:39:41 [ 1836.253588] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x43 Dec 29 11:39:41 [ 1836.253590] i2c_adapter i2c-0: master_xfer[0] W, addr=0x43, len=0 Dec 29 11:39:41 [ 1836.260782] tda9885/6/7: chip found @ 0x86 Dec 29 11:39:41 [ 1836.260795] i2c_adapter i2c-0: master_xfer[0] W, addr=0x43, len=4 Dec 29 11:39:41 [ 1836.268764] i2c_adapter i2c-0: client [tda9887] registered with bus id 0-0043 Dec 29 11:39:41 [ 1836.269773] i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x4b Dec 29 11:39:41 [ 1836.269780] i2c_adapter i2c-0: master_xfer[0] W, addr=0x4b, len=0 Dec 29 11:39:41 [ 1836.272135] saa7134[0]: registered device video0 [v4l2] Dec 29 11:39:41 [ 1836.273118] saa7134[0]: registered device vbi0 Dec 29 11:39:41 [ 1836.309716] saa7134[0]: pinnacle 300i dvb setup Dec 29 11:39:41 [ 1836.309895] i2c_adapter i2c-0: master_xfer[0] W, addr=0x1e, len=1 Dec 29 11:39:41 [ 1836.309949] i2c_adapter i2c-0: master_xfer[1] R, addr=0x1e, len=1 Dec 29 11:39:41 [ 1836.320823] DVB: registering new adapter (saa7134[0]). Dec 29 11:39:41 [ 1836.320962] DVB: registering frontend 0 (Zarlink MT352 DVB-T)... [...] [END /var/log/messages] If I try to tune any channel tzap shows an acceptable signal value but could not lock any channel and I get more I2C errors. Thanks, Tim
