Hi I change my account from romano_ferdinando@xxxxxxxx in darkside_moon83@xxxxxxxx I have suse 9.2 with this kernel 2.6.8-24-smp and I have these packages v4l-tools 3.94-2 pwlib-plugins-v4l 1.8.0-3 v4l-conf 3.94-2 pwlib 1.8.0-3 dvb 1.1.0_CVS20040812-7 devs 9.2-1 The PCI ID of PCTV SAT is 11bd:001c I obtained this value from dmesg bttv0: detected: Pinnacle PCTV Sat [card=94], PCI subsystem ID is 11bd:001c ********** >From the datasheet of pinnacle pc sat there are these information video digitalizer chip / control chip PCI Conexant CN 878 numeric tuner TV /radio /dati Conexant HM 1211 Input sat antenna F connector SAT IF passing band ( bandwidth) antenna output F connector SAT IF video input s video rca ********* If I type with root privileges # rcdvd start (it's like service dvb start) (load all dvb dviver) dmesg show me v4l2_common: unsupported module, tainting kernel. v4l1_compat: unsupported module, tainting kernel. video_buf: unsupported module, tainting kernel. saa7146: register extension 'dvb'. evdev_connect: evdev f7dcb880 handle f7dcb89c name event3 bttv: driver version 0.9.15 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 19 (level, low) -> IRQ 177 bttv0: Bt878 (rev 17) at 0000:02:07.0, irq: 177, latency: 64, mmio: 0xf7c00000 bttv0: detected: Pinnacle PCTV Sat [card=94], PCI subsystem ID is 11bd:001c bttv0: using: Pinnacle PCTV Sat [card=94,autodetected] bttv0: gpio: en=00000000, out=00000000 in=009f00fc [init] i2c-algo-bit.o: (0) scl=1, sda=1 i2c-algo-bit.o: (1) scl=1, sda=0 i2c-algo-bit.o: (2) scl=1, sda=1 i2c-algo-bit.o: (3) scl=0, sda=1 i2c-algo-bit.o: (4) scl=1, sda=1 i2c-algo-bit.o: bt878 #0 [sw] passed test. drivers/media/dvb/frontends/dib3000mb.c: did not found a DiBCom 3000-MB. bttv0: using tuner=-1 bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 .. ok bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI interrupt 0000:02:07.1[A] -> GSI 19 (level, low) -> IRQ 177 bt878(0): Bt878 (rev 17) at 02:07.1, irq: 177, latency: 64, memory: 0xf7d00000 bt878 find by dvb adap: checking "bt878 #0 [sw]" bt878 find by dvb adap: NOT found "bt878 #0 [sw]" mt312_read: ret == -121 i2c_adapter i2c-0: sendbytes: error - bailout. Please note that I have also on my PC another tv card (terrestrian) Typhoon tv tuner with chipset philips saa7134 then I type # modprobe dvb-bt8xx # modprobe cx24110 and the output of dmesg isn't changed Do you think I need some kind of firmware ? Perhaps scmain.c? Do you have any suggestions ? Thank for your interest ___________________________________ Yahoo! Messenger: chiamate gratuite in tutto il mondo http://it.beta.messenger.yahoo.com
