Hi I'm Romano Ferdinando I have a Suse 9.2 Pro. I have bought a Pinnacle PCTV SAT but I have some problems to use with my linux Can you help me? The card is recognized: nando@eclipse:~> /sbin/lspci ------------------ 0000:00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge (rev 02) 0000:00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge 0000:00:13.0 USB Controller: ATI Technologies Inc: Unknown device 4347 (rev 01) 0000:00:13.1 USB Controller: ATI Technologies Inc: Unknown device 4348 (rev 01) 0000:00:13.2 USB Controller: ATI Technologies Inc: Unknown device 4345 (rev 01) 0000:00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 18) 0000:00:14.1 IDE interface: ATI Technologies Inc: Unknown device 4349 0000:00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c 0000:00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 0000:00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller 0000:01:05.0 VGA compatible controller: ATI Technologies Inc Radeon 9100 IGP 0000:02:06.0 Multimedia controller: Philips Semiconductors SAA7134 (rev 01) 0000:02:07.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 0000:02:07.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 0000:02:08.0 Ethernet controller: 3Com Corporation 3Com 3C920B-EMB-WNM Integrated Fast Ethernet Controller (rev 40) 0000:02:09.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10) ---------- So I type : --------- # modprobe bttv i2c_hw=1 card=0x5E # modprobe dvb-bt8xx # modprobe cx24110 ----------- and dmesg show me ------------ Linux video capture interface: v1.00 [drm] Loading R200 Microcode v4l2_common: unsupported module, tainting kernel. video_buf: unsupported module, tainting kernel. bttv: driver version 0.9.15 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 19 (level, low) -> IRQ 177 bttv0: Bt878 (rev 17) at 0000:02:07.0, irq: 177, latency: 64, mmio: 0xf7c00000 bttv0: detected: Pinnacle PCTV Sat [card=94], PCI subsystem ID is 11bd:001c bttv0: using: Pinnacle PCTV Sat [card=94,insmod option] bttv0: gpio: en=00000000, out=00000000 in=009f00fc [init] bttv0: using tuner=-1 bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 .. ok bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI interrupt 0000:02:07.1[A] -> GSI 19 (level, low) -> IRQ 177 bt878(0): Bt878 (rev 17) at 02:07.1, irq: 177, latency: 64, memory: 0xf7d00000 ---------------- But I don't undestand the reason for which my system doesn't create the device /dev/dvb/adapter0/dvr0 and doesn't associate it to the stream of my Pinnacle card Which is the content of this device video0 and vbi0? What do they represent? Do you think that is necessary to use a firmware for this card? Do you have any suggestions to use this card? Thanks for your kindness Best Regards Romano Ferdinando in the following rows there are some info about my system : 2.6.8-24-smp there are these rpms: dvb 1.1.0_CVS20040812-7 libdvbpsi3 0.1.4-0.pm.3 v4l-tools 3.94-2 devs 9.2-1 ___________________________________ Yahoo! Messenger: chiamate gratuite in tutto il mondo http://it.beta.messenger.yahoo.com
