Hmm, sorry, I was supposed to reply to this thread... /Henrik ------------------- > Hi, > > I'm using kernel 2.6.11.8, which should have the patches you mention. > I am still seeing the same kinds of problem. Even with the asic_delay > patch posted earlier and asic_delay set to 10,30,40,50 and 100. > > When trying to scan, dmesg still tells me: > Set Frequency = [522000000] > dst_comm_init: Initializing DST.. > dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] > rdc_reset_state: Resetting state machine > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] > write_dst writing 07 f7 10 00 08 00 00 ea > dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] > read_dst reply is 0xff > dst_wait_dst_ready: dst wait ready after 1 > read_dst reply is 0x9 > 0xc1 0x11 0xbd 0x0 0x26 0x0 0x0 > dst_get_tuna: checksum failure? > Set Frequency = [522000000] > dst_comm_init: Initializing DST.. > dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] > rdc_reset_state: Resetting state machine > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] > write_dst writing 07 f7 10 00 08 00 80 6a > write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x07) > dst_error_recovery: Trying to return from previous errors... > dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] > dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] > dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] > read_dst reply is 0xff > dst_wait_dst_ready: dst wait ready after 1 > read_dst reply is 0x9 > 0xc1 0x11 0xbd 0x0 0x26 0x0 0x0 > dst_get_tuna: checksum failure? > > > Am I correct in my assumptions that 2.6.11.8 contains the patches? > > /Henrik ------------------- > Hans Gunnarsson wrote: > > > Hi all! > > > > I have patched the bttv driver with Manu's "anti-freeze" patch, and am > > using the latest CVS from dvb. The kernel is 2.6.11 > > > > Compiling and loading the modules are fine, but when I try to scan it > > returns Tuning failed! > > > > Any ideas? > > > > You need to use the bttv timout patch which i posted a while back along > with the freeze patch, for kernel = 2.6.11. > for kernel > 2.6.12-rc4 it has the freeze patch as well as the timeout > patch. > > Right now i am out of station and can't send you the patch.. > > > The following output on command line: > > > > hansg@muhammed:~/project/dvb_trunk/dvb-apps/util/scan>./dvbscan > > dvb-t/se-Stockholm_Nacka > > scanning dvb-t/se-Stockholm_Nacka > > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > > initial transponder 730000000 0 2 9 3 1 2 0 > > initial transponder 754000000 0 2 9 3 1 2 0 > > initial transponder 778000000 0 2 9 3 1 2 0 > > initial transponder 706000000 0 2 9 3 1 2 0 > > initial transponder 746000000 0 2 9 3 1 2 0 > > >>> tune to: > > 730000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 730000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > (tuning failed) > > > Yep, timed out.. > > > > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 754000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 754000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > (tuning failed) > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 778000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 778000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > (tuning failed) > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 706000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 706000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > (tuning failed) > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 746000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > > > WARNING: >>> tuning failed!!! > > >>> tune to: > > 746000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANS MISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > (tuning failed) > > WARNING: >>> tuning failed!!! > > ERROR: initial tuning failed > > dumping lists (0 services) > > Done. > > > > > > > > > > the interesting parts of dmesg: > > > > videodev: unsupported module, tainting kernel. > > Linux video capture interface: v1.00 > > tveeprom: unsupported module, tainting kernel. > > btcx_risc: unsupported module, tainting kernel. > > v4l2_common: unsupported module, tainting kernel. > > video_buf: unsupported module, tainting kernel. > > bttv: unsupported module, tainting kernel. > > bttv: driver version 0.9.15 loaded > > bttv: using 8 buffers with 2080k (520 pages) each for capture > > bttv: Bt8xx card found (0). > > ACPI: PCI interrupt 0000:06:02.0[A] -> GSI 18 (level, low) -> IRQ 217 > > bttv0: Bt878 (rev 17) at 0000:06:02.0, irq: 217, latency: 32, mmio: > > 0xdfefe000 > > bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID > > is 1822:0001 > > bttv0: using: Twinhan DST + clones [card=113,insmod option] > > bttv0: gpio: en=00000000, out=00000000 in=00f500fd [init] > > bttv0: using tuner=4 > > tuner: unsupported module, tainting kernel. > > bttv0: add subdevice "dvb0" > > or51211: unsupported module, tainting kernel. > > cx24110: unsupported module, tainting kernel. > > dvb_core: unsupported module, tainting kernel. > > bt878: unsupported module, tainting kernel. > > bt878: AUDIO driver version 0.0.0 loaded > > bt878: Bt878 AUDIO function found (0). > > ACPI: PCI interrupt 0000:06:02.1[A] -> GSI 18 (level, low) -> IRQ 217 > > bt878(0): Bt878 (rev 17) at 06:02.1, irq: 217, latency: 32, memory: > > 0xdfeff000 > > dst: unsupported module, tainting kernel. > > dst_ca: unsupported module, tainting kernel. > > sp887x: unsupported module, tainting kernel. > > mt352: unsupported module, tainting kernel. > > nxt6000: unsupported module, tainting kernel. > > dvb_bt8xx: unsupported module, tainting kernel. > > DVB: registering new adapter (bttv0). > > dst_get_device_id: Recognise [DTT-CI] > > DST type : terrestrial > > DST type flags : 0x2 ts204 0x10 firmware version = 2 > > DVB: registering frontend 0 (DST DVB-T)... > > read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xf7) > > dst_error_recovery: Trying to return from previous errors... > > read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xf7) > > dst_error_recovery: Trying to return from previous errors... > > dst_error_bailout: Trying to bailout from previous error... > > dst_write_tuna: read verify not successful. > > > No doubts that it timed out. > > > Manu. > > > _______________________________________________ > > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >
