Re: [PATCH v2 09/19] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 01/03/2017 10:57 PM, Steve Longerbeam wrote:
> Enables the ADV7180 decoder sensor. The ADV7180 connects to the
> parallel-bus mux input on ipu1_csi0_mux.
> 
> On the sabreauto, two analog video inputs are routed to the ADV7180,
> composite on Ain1, and composite on Ain3. Those inputs are defined
> via inputs and input-names under the ADV7180 node. The ADV7180 power
> pin is via max7310_b port expander.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
> ---
>  arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 56 ++++++++++++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> index 83ac2ff..30ee378 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> @@ -147,10 +147,42 @@
>  				gpio-controller;
>  				#gpio-cells = <2>;
>  			};
> +
> +			camera: adv7180@21 {

adv7180: camera@21

> +				compatible = "adi,adv7180";
> +				reg = <0x21>;
> +				powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
> +				interrupt-parent = <&gpio1>;
> +				interrupts = <27 0x8>;
> +				inputs = <0x00 0x02>;
> +				input-names = "ADV7180 Composite on Ain1",
> +						"ADV7180 Composite on Ain3";
> +
> +				port {
> +					adv7180_to_ipu1_csi0_mux: endpoint {
> +						remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> +						bus-width = <8>;
> +					};
> +				};
> +			};
>  		};
>  	};
>  };
>  
> +&ipu1_csi0_from_ipu1_csi0_mux {
> +	bus-width = <8>;
> +};
> +
> +&ipu1_csi0_mux_from_parallel_sensor {
> +	remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
> +	bus-width = <8>;
> +};
> +
> +&ipu1_csi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ipu1_csi0>;
> +};
> +
>  &clks {
>  	assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
>  			  <&clks IMX6QDL_PLL4_BYPASS>,
> @@ -451,6 +483,30 @@
>  			>;
>  		};
>  
> +		pinctrl_ipu1_csi0: ipu1grp-csi0 {

Please rename node name to ipu1csi0grp.

> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04   0x80000000
> +				MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05   0x80000000
> +				MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06   0x80000000
> +				MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07   0x80000000
> +				MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08   0x80000000
> +				MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09   0x80000000
> +				MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10  0x80000000
> +				MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11  0x80000000
> +				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12  0x80000000
> +				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13  0x80000000
> +				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14  0x80000000
> +				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15  0x80000000
> +				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16  0x80000000
> +				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17  0x80000000
> +				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18  0x80000000
> +				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19  0x80000000
> +				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000
> +				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC    0x80000000
> +				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC   0x80000000
> +			>;
> +		};
> +
>  		pinctrl_pwm3: pwm1grp {
>  			fsl,pins = <
>  				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
> 

--
With best wishes,
Vladimir
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel



[Index of Archives]     [Linux Driver Backports]     [DMA Engine]     [Linux GPIO]     [Linux SPI]     [Video for Linux]     [Linux USB Devel]     [Linux Coverity]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux