> +static const char slic_stats_strings[][ETH_GSTRING_LEN] = {
> + "rx_packets ",
> + "rx_bytes ",
> + "rx_multicasts ",
> + "rx_errors ",
> + "rx_buff_miss ",
> + "rx_tp_csum ",
> + "rx_tp_oflow ",
> + "rx_tp_hlen ",
> + "rx_ip_csum ",
> + "rx_ip_len ",
Are there any other drivers which pad the statistics strings?
> +static void slic_set_link_autoneg(struct slic_device *sdev)
> +{
> + unsigned int subid = sdev->pdev->subsystem_device;
> + u32 val;
> +
> + if (sdev->is_fiber) {
> + /* We've got a fiber gigabit interface, and register 4 is
> + * different in fiber mode than in copper mode.
> + */
> + /* advertise FD only @1000 Mb */
> + val = MII_ADVERTISE << 16 | SLIC_PAR_ADV1000XFD |
> + SLIC_PAR_ASYMPAUSE_FIBER;
> + /* enable PAUSE frames */
> + slic_write(sdev, SLIC_REG_WPHY, val);
> + /* reset phy, enable auto-neg */
> + val = MII_BMCR << 16 | SLIC_PCR_RESET | SLIC_PCR_AUTONEG |
> + SLIC_PCR_AUTONEG_RST;
> + slic_write(sdev, SLIC_REG_WPHY, val);
> + } else { /* copper gigabit */
> + /* We've got a copper gigabit interface, and register 4 is
> + * different in copper mode than in fiber mode.
> + */
> + /* advertise 10/100 Mb modes */
> + val = MII_ADVERTISE << 16 | SLIC_PAR_ADV100FD |
> + SLIC_PAR_ADV100HD | SLIC_PAR_ADV10FD | SLIC_PAR_ADV10HD;
> + /* enable PAUSE frames */
> + val |= SLIC_PAR_ASYMPAUSE;
> + /* required by the Cicada PHY */
> + val |= SLIC_PAR_802_3;
> + slic_write(sdev, SLIC_REG_WPHY, val);
> +
> + /* advertise FD only @1000 Mb */
> + val = MII_CTRL1000 << 16 | SLIC_PGC_ADV1000FD;
> + slic_write(sdev, SLIC_REG_WPHY, val);
> +
> + if (subid != PCI_SUBDEVICE_ID_ALACRITECH_CICADA) {
> + /* if a Marvell PHY enable auto crossover */
> + val = SLIC_MIICR_REG_16 | SLIC_MRV_REG16_XOVERON;
> + slic_write(sdev, SLIC_REG_WPHY, val);
> +
> + /* reset phy, enable auto-neg */
> + val = MII_BMCR << 16 | SLIC_PCR_RESET |
> + SLIC_PCR_AUTONEG | SLIC_PCR_AUTONEG_RST;
> + slic_write(sdev, SLIC_REG_WPHY, val);
> + } else {
> + /* enable and restart auto-neg (don't reset) */
> + val = MII_BMCR << 16 | SLIC_PCR_AUTONEG |
> + SLIC_PCR_AUTONEG_RST;
> + slic_write(sdev, SLIC_REG_WPHY, val);
> + }
> + }
> + sdev->autoneg = true;
> +}
Could this be pulled out into a standard PHY driver? All the SLIC
SLIC_PCR_ defines seems to be the same as those in mii.h. This could
be a standard PHY hidden behind a single register.
Andrew
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
