Introduce accessor functions that read and write registers by using a
register offset.
This is in preparation to replace the register addressing by means of the
slic_regs struct with an addressing by means of offsets.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@xxxxxx>
---
drivers/staging/slicoss/slic.h | 24 ++++++++
drivers/staging/slicoss/slichw.h | 113 ++++++++++++++++++++++++++++++++++++++
drivers/staging/slicoss/slicoss.c | 1 +
3 files changed, 138 insertions(+)
diff --git a/drivers/staging/slicoss/slic.h b/drivers/staging/slicoss/slic.h
index cc0afee..08d9f5b 100644
--- a/drivers/staging/slicoss/slic.h
+++ b/drivers/staging/slicoss/slic.h
@@ -418,6 +418,7 @@ struct adapter {
dma_addr_t phys_shmem;
u32 isrcopy;
__iomem struct slic_regs *slic_regs;
+ void __iomem *regs;
unsigned char state;
unsigned char linkstate;
unsigned char linkspeed;
@@ -487,6 +488,29 @@ struct adapter {
struct slicnet_stats slic_stats;
};
+static inline u32 slic_read32(struct adapter *adapter, unsigned int reg)
+{
+ return ioread32(adapter->regs + reg);
+}
+
+static inline void slic_write32(struct adapter *adapter, unsigned int reg,
+ u32 val)
+{
+ iowrite32(val, adapter->regs + reg);
+}
+
+static inline void slic_write64(struct adapter *adapter, unsigned int reg,
+ u32 val, u32 hiaddr)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&adapter->bit64reglock, flags);
+ slic_write32(adapter, SLIC_REG_ADDR_UPPER, hiaddr);
+ slic_write32(adapter, reg, val);
+ mmiowb();
+ spin_unlock_irqrestore(&adapter->bit64reglock, flags);
+}
+
#define UPDATE_STATS(largestat, newstat, oldstat) \
{ \
if ((newstat) < (oldstat)) \
diff --git a/drivers/staging/slicoss/slichw.h b/drivers/staging/slicoss/slichw.h
index 9723b4a..f06450e 100644
--- a/drivers/staging/slicoss/slichw.h
+++ b/drivers/staging/slicoss/slichw.h
@@ -289,6 +289,119 @@ struct slic_rspbuf {
u32 pad2[4];
};
+/* Reset Register */
+#define SLIC_REG_RESET 0x0000
+/* Interrupt Control Register */
+#define SLIC_REG_ICR 0x0008
+/* Interrupt status pointer */
+#define SLIC_REG_ISP 0x0010
+/* Interrupt status */
+#define SLIC_REG_ISR 0x0018
+/*
+ * Header buffer address reg
+ * 31-8 - phy addr of set of contiguous hdr buffers
+ * 7-0 - number of buffers passed
+ * Buffers are 256 bytes long on 256-byte boundaries.
+ */
+#define SLIC_REG_HBAR 0x0020
+/*
+ * Data buffer handle & address reg
+ * 4 sets of registers; Buffers are 2K bytes long 2 per 4K page.
+ */
+#define SLIC_REG_DBAR 0x0028
+/*
+ * Xmt Cmd buf addr regs.
+ * 1 per XMT interface
+ * 31-5 - phy addr of host command buffer
+ * 4-0 - length of cmd in multiples of 32 bytes
+ * Buffers are 32 bytes up to 512 bytes long
+ */
+#define SLIC_REG_CBAR 0x0030
+/* Write control store */
+#define SLIC_REG_WCS 0x0034
+/*
+ * Response buffer address reg.
+ * 31-8 - phy addr of set of contiguous response buffers
+ * 7-0 - number of buffers passed
+ * Buffers are 32 bytes long on 32-byte boundaries.
+ */
+#define SLIC_REG_RBAR 0x0038
+/* Read statistics (UPR) */
+#define SLIC_REG_RSTAT 0x0040
+/* Read link status */
+#define SLIC_REG_LSTAT 0x0048
+/* Write Mac Config */
+#define SLIC_REG_WMCFG 0x0050
+/* Write phy register */
+#define SLIC_REG_WPHY 0x0058
+/* Rcv Cmd buf addr reg */
+#define SLIC_REG_RCBAR 0x0060
+/* Read SLIC Config*/
+#define SLIC_REG_RCONFIG 0x0068
+/* Interrupt aggregation time */
+#define SLIC_REG_INTAGG 0x0070
+/* Write XMIT config reg */
+#define SLIC_REG_WXCFG 0x0078
+/* Write RCV config reg */
+#define SLIC_REG_WRCFG 0x0080
+/* Write rcv addr a low */
+#define SLIC_REG_WRADDRAL 0x0088
+/* Write rcv addr a high */
+#define SLIC_REG_WRADDRAH 0x0090
+/* Write rcv addr b low */
+#define SLIC_REG_WRADDRBL 0x0098
+/* Write rcv addr b high */
+#define SLIC_REG_WRADDRBH 0x00a0
+/* Low bits of mcast mask */
+#define SLIC_REG_MCASTLOW 0x00a8
+/* High bits of mcast mask */
+#define SLIC_REG_MCASTHIGH 0x00b0
+/* Ping the card */
+#define SLIC_REG_PING 0x00b8
+/* Dump command */
+#define SLIC_REG_DUMP_CMD 0x00c0
+/* Dump data pointer */
+#define SLIC_REG_DUMP_DATA 0x00c8
+/* Read card's pci_status register */
+#define SLIC_REG_PCISTATUS 0x00d0
+/* Write hostid field */
+#define SLIC_REG_WRHOSTID 0x00d8
+/* Put card in a low power state */
+#define SLIC_REG_LOW_POWER 0x00e0
+/* Force slic into quiescent state before soft reset */
+#define SLIC_REG_QUIESCE 0x00e8
+/* Reset interface queues */
+#define SLIC_REG_RESET_IFACE 0x00f0
+/*
+ * Register is only written when it has changed.
+ * Bits 63-32 for host i/f addrs.
+ */
+#define SLIC_REG_ADDR_UPPER 0x00f8
+/* 64 bit Header buffer address reg */
+#define SLIC_REG_HBAR64 0x0100
+/* 64 bit Data buffer handle & address reg */
+#define SLIC_REG_DBAR64 0x0108
+/* 64 bit Xmt Cmd buf addr regs. */
+#define SLIC_REG_CBAR64 0x0110
+/* 64 bit Response buffer address reg.*/
+#define SLIC_REG_RBAR64 0x0118
+/* 64 bit Rcv Cmd buf addr reg*/
+#define SLIC_REG_RCBAR64 0x0120
+/* Read statistics (64 bit UPR) */
+#define SLIC_REG_RSTAT64 0x0128
+/* Download Gigabit RCV sequencer ucode */
+#define SLIC_REG_RCV_WCS 0x0130
+/* Write VlanId field */
+#define SLIC_REG_WRVLANID 0x0138
+/* Read Transformer info */
+#define SLIC_REG_READ_XF_INFO 0x0140
+/* Write Transformer info */
+#define SLIC_REG_WRITE_XF_INFO 0x0148
+/* Write card ticks per second */
+#define SLIC_REG_TICKS_PER_SEC 0x0170
+
+#define SLIC_REG_HOSTID 0x1554
+
struct slic_regs {
u32 slic_reset; /* Reset Register */
u32 pad0;
diff --git a/drivers/staging/slicoss/slicoss.c b/drivers/staging/slicoss/slicoss.c
index 577c2d2..edae0f7 100644
--- a/drivers/staging/slicoss/slicoss.c
+++ b/drivers/staging/slicoss/slicoss.c
@@ -2920,6 +2920,7 @@ static int slic_init_adapter(struct net_device *netdev,
adapter->slotnumber = ((pcidev->devfn >> 3) & 0x1F);
adapter->functionnumber = (pcidev->devfn & 0x7);
adapter->slic_regs = memaddr;
+ adapter->regs = memaddr;
adapter->irq = pcidev->irq;
adapter->chipid = chip_idx;
adapter->port = 0;
--
1.9.1
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
