Replace `enum marb_bits` in "plx9080.h" with a bunch of macros defining
values for the MARBR and DMAARB registers (which are the same
Mode/Arbitation register at two different offsets). Use the prefix
`PLX_MARBR_` for the macros. Make use of the `BIT(x)` and
`GENMASK(h,l)` macros to define the values.
Signed-off-by: Ian Abbott <abbotti@xxxxxxxxx>
---
drivers/staging/comedi/drivers/plx9080.h | 60 +++++++++++++++++++++-----------
1 file changed, 40 insertions(+), 20 deletions(-)
diff --git a/drivers/staging/comedi/drivers/plx9080.h b/drivers/staging/comedi/drivers/plx9080.h
index 140135c..0bcdbad 100644
--- a/drivers/staging/comedi/drivers/plx9080.h
+++ b/drivers/staging/comedi/drivers/plx9080.h
@@ -81,26 +81,46 @@ struct plx_dma_desc {
/* DMA Arbitration Register (alias of MARBR). */
#define PLX_REG_DMAARB 0x00ac
-enum marb_bits {
- MARB_LLT_MASK = 0x000000ff, /* Local Bus Latency Timer */
- MARB_LPT_MASK = 0x0000ff00, /* Local Bus Pause Timer */
- MARB_LTEN = 0x00010000, /* Latency Timer Enable */
- MARB_LPEN = 0x00020000, /* Pause Timer Enable */
- MARB_BREQ = 0x00040000, /* Local Bus BREQ Enable */
- MARB_DMA_PRIORITY_MASK = 0x00180000,
- /* local bus direct slave give up bus mode */
- MARB_LBDS_GIVE_UP_BUS_MODE = 0x00200000,
- /* direct slave LLOCKo# enable */
- MARB_DS_LLOCK_ENABLE = 0x00400000,
- MARB_PCI_REQUEST_MODE = 0x00800000,
- MARB_PCIV21_MODE = 0x01000000, /* pci specification v2.1 mode */
- MARB_PCI_READ_NO_WRITE_MODE = 0x02000000,
- MARB_PCI_READ_WITH_WRITE_FLUSH_MODE = 0x04000000,
- /* gate local bus latency timer with BREQ */
- MARB_GATE_TIMER_WITH_BREQ = 0x08000000,
- MARB_PCI_READ_NO_FLUSH_MODE = 0x10000000,
- MARB_USE_SUBSYSTEM_IDS = 0x20000000,
-};
+/* Local Bus Latency Timer */
+#define PLX_MARBR_LT(x) (BIT(0) * ((x) & 0xff))
+#define PLX_MARBR_LT_MASK GENMASK(7, 0)
+#define PLX_MARBR_LT_SHIFT 0
+/* Local Bus Pause Timer */
+#define PLX_MARBR_PT(x) (BIT(8) * ((x) & 0xff))
+#define PLX_MARBR_PT_MASK GENMASK(15, 8)
+#define PLX_MARBR_PT_SHIFT 8
+/* Local Bus Latency Timer Enable */
+#define PLX_MARBR_LTEN BIT(16)
+/* Local Bus Pause Timer Enable */
+#define PLX_MARBR_PTEN BIT(17)
+/* Local Bus BREQ Enable */
+#define PLX_MARBR_BREQEN BIT(18)
+/* DMA Channel Priority */
+#define PLX_MARBR_PRIO_ROT (BIT(19) * 0) /* Rotational priority */
+#define PLX_MARBR_PRIO_DMA0 (BIT(19) * 1) /* DMA channel 0 has priority */
+#define PLX_MARBR_PRIO_DMA1 (BIT(19) * 2) /* DMA channel 1 has priority */
+#define PLX_MARBR_PRIO_MASK GENMASK(20, 19)
+/* Local Bus Direct Slave Give Up Bus Mode */
+#define PLX_MARBR_DSGUBM BIT(21)
+/* Direct Slace LLOCKo# Enable */
+#define PLX_MARBR_DSLLOCKOEN BIT(22)
+/* PCI Request Mode */
+#define PLX_MARBR_PCIREQM BIT(23)
+/* PCI Specification v2.1 Mode */
+#define PLX_MARBR_PCIV21M BIT(24)
+/* PCI Read No Write Mode */
+#define PLX_MARBR_PCIRNWM BIT(25)
+/* PCI Read with Write Flush Mode */
+#define PLX_MARBR_PCIRWFM BIT(26)
+/* Gate Local Bus Latency Timer with BREQ */
+#define PLX_MARBR_GLTBREQ BIT(27)
+/* PCI Read No Flush Mode */
+#define PLX_MARBR_PCIRNFM BIT(28)
+/*
+ * Make reads from PCI Configuration register 0 return Subsystem ID and
+ * Subsystem Vendor ID instead of Device ID and Vendor ID
+ */
+#define PLX_MARBR_SUBSYSIDS BIT(29)
/* Big/Little Endian Descriptor Register */
#define PLX_REG_BIGEND 0x000c
--
2.8.1
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
